147210 General Electric Range - Instructions

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats g ... Read more ood now, makes great cornbread and biscuits, the wife helps the oven do this.

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

I followed the "Test Procedures" on your site { VOM to test the Temperature Sensor and observed the intensity of the Igniter } and found both items were not at specs. Although your video did not depict my model oven exactly, it showed me enough details on how to get to and change out the parts. IE: The connector plug for the Flat Style ... Read more Oven Igniter had to be accessed through the Warning Draw and not the Oven as shown in the video. A minor issue.
I found your test and safety procedures, how to video's and ease of ordering the required parts fantastic. Most importantly the parts arrived in one day and a half. A very satisfying experience, Thank you

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 yea ... Read more r old oven,it was very easy/.

This would've been an easy repair, but I ran into some complications.

First I removed the thumb screws holding the bottom oven pan, took the pan out, and also took the bottom panel off the front of the oven.

This gives you access to the burner assembly. I disconnected the wire to the ignitor. I then removed one s ... Read more crew at the front, and two in the back of the burner assembly with a 1/4 socket wrench.

The burner assembly came out. I tested the ignitor for continutiy with a multimeter to ensure this was the faulty part. There was not continuity, so I knew the ignitor needed to be replaced.

This was when I tried to unscrew the ignitor, and both screws stripped their threads on the burner mounting plate. Complication #1. Seems with age, that mounting plate tightened up on the screws.

I cut the screw heads off with a dremel and cutting wheel to get them out. I'm glad I did this before ordering the new part because I needed to order the replacement screws too.

The burner mounting plate for the ignitor needed to be re-tapped to get the new screws in with a 10-32 tap and power drill.

Once the mounting plate was properly rethreaded, I attached the new ignitor, and reattached the burner assembly to the oven.

When trying to connect the wires, the plastic connectors wouldn't click together. They matched up fine, but wouldn't go all the way in. Complication #2. While the plastic connectors were properly mated, the inside pins were both female. The old ignitor had male pins on it, the new one had female pins. So I removed the burner assembly again, cut off the new ignitor connector and spliced in the old ignitor connector with the included porcelain wire nuts.

I put the oven back together again, fired it up, and it worked great.

Removed the screw from the broken piece and put the new piece on and put the screw on.

opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A ... Read more screwdriver is the only tool required.

Took longer to open the box.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

I unscrewed to old glide and replaced it then re attached the screw

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the i ... Read more gniter is the problem.

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using ... Read more your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.