146702-0654-99 Briggs and Stratton Engine - Parts

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar symptoms can come from a frayed rope, seized engine, bent starter housing, broken pawls, or weak return spring, so check those items first. ...Read moreMatch the replacement to the full engine model, type, code, and equipment model. Work on a cool engine with the spark plug lead removed. Release spring tension slowly and keep your face and hands clear of the starter housing. Route the rope correctly, confirm smooth return, and reinstall every guard before starting the engine.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.

An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carb...Read moreuretor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.

This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the breather. Over time it may become brittle and begin to crack eventually requiring a replacement. For the proper...Read more application please refer to the appropriate diagrams of your model. This high-quality part is made of durable composite material and is sold individually. You will need a screwdriver and a wrench set to remove and reattach the breather.

This OEM engine screw is a genuine Briggs & Stratton replacement fastener designed for secure, vibration-resistant attachment of engine components in small gasoline engines and outdoor power equipment. Manufactured to exact factory specifications, it provides proper thread engagement and clamping force to help prevent loosening, reduce vi...Read morebration, and maintain long-term engine reliability under operating stress. Built with durable, corrosion-resistant materials for extended service life, it is an ideal replacement when original screws are missing, stripped, or worn, helping ensure safe assembly, consistent performance, and proper engine operation.

This replacement screw is a genuine OEM sourced hardware designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It has multiple applications depending on the unit. Please always make sure to check appropriate diagrams for correct location and use of this hardware. This metal screw is sold individually.