1440 - Parts

This authentic item is sourced directly from the original equipment manufacturer for use with Ariens riding lawn mowers and garden tractors. It is an identical replacement for a missing or a faulty roller that was installed on a new unit. The part helps to support the deck, please make sure to refer to the appropriate diagrams of your mod...Read moreel for the correct location and application of this component. This high-quality part is made of durable rubber and is sold individually. Keep in mind the #02747651 Roller Clevis , the #02747500 Pin, Clevis and the #05503600 Flange Bushing are all sold separately.

This tension spring, also known as a coil spring or extension spring, is an authentic manufacturer replacement part used in a variety of outdoor power equipment. It is a cylindrical, steel spring with one hook/ring on each end, which is used to hook on to the equipment parts. The spring is responsible for providing tension or resistance t...Read moreo various parts for controlled movement and added stability. It is typically located in areas such as throttle controls, idler pulleys, and belts. The tension spring can rust or break over time, leading to loose components, equipment instability, and potentially causing damage. To remove and replace the tension spring, use needle nose pliers or a spring hook tool to grab the hooks and gently pry them off. Hook the new spring on the attachment points and ensure that it can maintain the required tension.

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton and Troy-Bilt equipment. This is an identical replacement for a missing or a faulty push nut that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct locat...Read moreion and application of this component. Keep in mind this high-quality push nut is made of durable plastic with metal and is sold in a pack of two.

This ribbed-neck stud in your lawn equipment is a threaded bolt that attaches to the wheel hub. It may also be referred to as a wheel stud. It secures the wheel to the hub and has a 7/16-inch diameter, a 14 threads per inch pitch, and a length of 1.6 inches. If the wheel feels loose or wobbles, the stud may be broken or damaged. Look for ...Read morevisible cracks, bends, or breaks in the stud. A broken stud can cause wheel misalignment or detachment and additional stress on the wheel assembly. To remove the stud, turn off the equipment, engage the safety mechanisms, and use a jack to elevate the equipment. Remove the wheel by loosening and removing the nuts, then slide it off the hub. With the wheel removed, use a hammer to drive the stud out of the hub. You need to use a press to install the new stud. When replacing the studs in your machine, consult your user guide to ensure you purchase the correct number of studs as they are sold individually.

This is a genuine Ariens replacement part. The V-belt is commonly found in Ariens lawn tractors. This part is made of layered rubber and fabric, and is used to connect the clutch with one of the mower blades, which will cause the blade to spin when the clutch is engaged. Please be aware that there are different belts used in the machin...Read moree. Refer to the parts diagram to be sure of ordering the correct part. This part is sold individually.

This OEM part is a zerk fitting that is sometimes called a grease fitting, lube fitting, grease zerk, or Alemite fitting. It is a metal nipple that you connect a grease gun to, allowing you to lubricate the moving parts in your lawn equipment, usually on joints or bearings. This fitting is 1/4 inch wide, has 28 threads per inch, and a thr...Read moreeaded portion that is .256 inches long. If the fitting is broken, you may notice that your machine is moving sluggishly, or the fitting may appear cracked or clogged with debris. It is important to replace a damaged fitting right away, because if you do not, debris can prevent the fitting from accepting grease and the moving parts of your machine will wear out faster and eventually break down completely. To replace the fitting, you will need to use a wrench to remove it from your machine. Keep in mind that this replacement part is sold separately, so you may want to consider stocking up on fittings before you need them. Since the fittings on your machine wear out at the same rate, having a few extra on hand can save you time and hassle down the road.

This replacement part is used to connect the mower blade to the base of the mower deck. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. The Bearing Slinger is most often located on the spindle housing of the mower deck and needs to be replaced if it is broken, worn, or damaged. This part is know...Read moren to become worn through regular use of your machine. Customers rated this repair as Medium difficulty.