143R Husqvarna Brush Cutter - Parts

This is a Genuine OEM replacement part used on Ride Mowers/Lawn Tractors. This is the Wheel that helps to support the Deck and allows it to move around easier. This Wheel is made out of Plastic and it is Sold Individually. Please note the Bolt and Nut used to secure this Wheel are Sold Separately. To replace this item you would need a Wrench.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This metal square key is designed to prevent the rear wheel of your lawn equipment from slipping. Approximately sized at 3/16 x 2, it fits into the groove found on the axle and the hub of the wheel, ensuring proper alignment of the two parts. If the machine becomes hard to turn or maneuver or it makes a grinding or clicking sound, your sq...Read moreuare key may be worn out. Visually inspecting this part for bends and cracks can confirm this. You may also notice that the rear wheel is wobbling or falling off. A worn square key can cause damage to the wheel assembly of the machine, leading to costly repairs or even the need to purchase a new one. To prevent that, you need to replace a broken square key as soon as possible. Replacing the square key is a simple process. After turning your lawn equipment off and letting it cool down, you need to use a jack to lift the rear of it off the ground. Remove the wheel from the axle by using a socket to remove any bolts or nuts holding it in place. With pliers, you can then take the square key off the machine. This replacement part is sold individually and is sourced directly from its original manufacturer.

This is a genuine replacement part sourced directly from the manufacturer. The engine pulley is commonly found in Craftsman lawn tractors and riding mowers. This part is made of metal, and is used in conjunction with the belt to transfer power from the engine to the machine. You will require a wrench when replacing this item. The engine pulley is sold as an individual replacement part.

This genuine OEM idler pulley is sourced directly from the original manufacturer and is designed for use with select riding lawn mowers from Husqvarna, Poulan, and Jonsered. It mounts to the top of the mower’s deck assembly and plays a critical role in guiding the mower deck belt along its proper path, ensuring smooth and efficient operat...Read moreion. Made from durable materials for long-lasting performance, this idler pulley is available as an individual replacement part. Installation is straightforward and requires a ratchet and hex socket set. For best results, refer to your equipment’s model diagram to confirm compatibility and proper placement. Restore your mower’s cutting performance and belt alignment with this reliable, manufacturer-approved component.

This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the pinion to the transmission axle to allow the two parts to rotate in unison. This drive pawl is priced as a single item, please note two may be needed.

This is a genuine Craftsman part for use with Lawn Mowers. The drive gear attaches on the inner side of the drive wheel. The drive gear meshes with the pinion in the drive wheel to propel the mower. The most common reason for replacing the gear is when the self-propel system will not drive one or both wheels. This part is sold individuall...Read morey. The tools that you will need to replace the gear is a 12mm socket and snap-ring pliers.

This is a genuine Husqvarna and Poulan part for use with Lawn Tractors. The steering shaft kit contains the parts needed to connect the steering wheel to the sector gear. The most common reason for replacing the steering shaft is when the steering wheel will not turn the mower. Here is a list of tools that are needed to install the steeri...Read moreng shaft are a 3/4" socket, mallet, 3/8" socket, floor jack, pliers, and a 9/16" socket.

It is an authentic replacement cap-spindle that is supplied by the original equipment manufacturer for use with Poulan, Ryobi and Husqvarna riding lawn mowers and garden tractors. It is an identical replacement for a missing or damaged cap that was originally installed on a new equipment. The cap is utilized to cover the spindle. Make sur...Read moree to check the appropriate diagrams of your model for the exact location and application of this hardware. This high-quality cap-spindle is made of durable plastic material and is sold individually.

This 25mm blade nut is a fastener that secures the blade to the spindle or shaft of your lawn equipment. It is located at the center of the blade. Signs of a broken blade nut include looseness, stripping, cracks, or excessive wear. Failing to replace a broken blade nut can result in a loose or dislodged blade during operation. To unthread...Read more the blade nut on your machine, use a wrench or socket to loosen it. This OEM component is sold individually. To ensure you have the correct number of blade nuts for your machine, refer to the user guide as your equipment may require multiple blade nuts. Consider replacing all of the nuts in one go as they wear out at similar rates.

This is an authentic replacement part sourced directly from the manufacturer. The return spring is commonly found in Craftsman lawn tractors and riding mowers. This part is made of metal, and is generally used to apply tension to the idler arm. You may require pliers when replacing this item. The return spring is available as an individual replacement part.