142LE Husqvarna Chainsaw - Parts

It is an authentic manufacturer-sourced part which is specially made for Poulan and Husqvarna chainsaws. The part is utilized on a chainsaw to to adjust the blade to the correct tension. A correctly adjusted chainsaw blade will last longer and cut better. It provides an identical replacement for a missing or a faulty component that was in...Read morestalled on a new unit. Keep in mind this high-quality pin-bar adjust is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. NOTE: Here is the link to our article on How to Tighten a Chainsaw Chain

This is a genuine manufacturer approved replacement part designed for use with chainsaws. This part is an important safety feature because it prevents the chainsaw chain from flying off the bar if it breaks or comes loose from its track. It is made out of metal and it is sold individually. Please note the screw used to secure it is sold separately.

This Bar Pin Adjuster is an OEM part used to adjust the tension on the bar, which loosens or tightens the chain. It attaches to the slot in the bar, and the chainsaw bar adjusting screw. Installation is rated as "Easy" and requires a screwdriver. Refer to your make, model and diagram to ensure this part is correct.

This is an authentic OEM part for use with Craftsman Chainsaws. The recoil starter repair kit replaces the parts of the engine\\\'s recoil starter susceptible to normal wear. The most common reason for replacing the recoil starter repair kit is if the engine won't turn over when starter rope is pulled the Starter rope pulls too easily (an...Read mored without resistance) the Starter hub is not engaging the flywheel or the Starter hub is not turning with the pulley (when the rope is pulled). This part includes starter pulley the assist spring and the starter hub. Here is a list of tools that are needed to install the recoil starter repair kit Phillip's screwdriver, Torx drivers, long-nosed pliers, and scissors or wire cutters (optional).

Genuine Poulan replacement part, this item is sold individually. This Screw is used on the Chainsaws listed below. It is used to attach the Cylinder Shield to the main body of the Chainsaw. This is a size T-25 Torx Screw.

This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

It is a genuine item that is supplied by the original manufacturer for use with Poulan and Weed Eater chainsaws. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a right fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on ...Read morea new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer-clutch is included. You may need a screwdriver and a wrench set to perform this repair.

This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.

This replacement carburetor gasket is specially made for use with gas chainsaws. It is supplied directly from original equipment manufacturer. This gasket provides an air tight seal between the carburetor and the plate. It is made out of compound material and it is sold individually. You will need a screwdriver and a wrench to complete this repair.

This is a genuine part sourced directly from the manufacturer. The Washer-thrust is commonly found in Poulan, Husqvarna and Jonsered chainsaws. The washer is utilized to provide a tight fit between connected parts. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. Refer to the diagrams ...Read morefor your model to ensure the exact location and the correct application of this part. Keep in mind this washer is made of durable metal and is sold as an individual item.

This replacement OEM part is specially designed for Poulan chainsaws. It is the tool-less knob assembly that attaches to the chain brake assembly. The knob provides a user with a comfortable grip to adjust the chain tension. It has internal threads which allow it to be secured and removed without any tools. Check the owner's manual and th...Read moree diagrams of your model for the correct application of this part. One durable component is included. Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time before you start the chainsaw.

This replacement part is an authentic OEM screw designed for use with gas chainsaws and trimmers. This item is generally used to secure the housing of the equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.