1420 - Parts

This screw is sold individually.

This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually. NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.

This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and is an exact replacement for various pressure washers. If the cleaning solution will not dispense, it is possible that you need a new Chemi...Read morecal Injection Kit. Inspect it for signs of wear or damage and replace it if needed. This part is known to wear over time. You will need a wrench set to complete this repair. Customers rate this repair as Easy.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This suction tube is compatible with various makes and models of airless paint sprayers and is sold as an individual OEM part. It draws paint from the container/reservoir and delivers it to the sprayer for application. This tube has a built-in filter attached, to prevent dust, dirt, or debris from entering the sprayer system. When suction...Read more tubes become clogged/blocked, damaged, or lose their suction, they can become inoperable and will lose any and all function. It is recommended that you regularly inspect the tube for damage or clogs, and if you notice your sprayer leaking from connection points around the tube or inconsistent spray patterns and suction ability, the tube is likely needing replacement. To replace this tube within your paint sprayer assembly, disconnect your sprayer from power and relieve the pressure within the sprayer. Drain all paint from the sprayer and paint reservoir to avoid mess. Remove the old suction tube by unscrewing it and/or any securing hardware, and then install the new tube with the same process as before. With the new tube installed, perform a test run with the sprayer to ensure the suction tube works properly before using it normally.

This is a genuine OEM sourced replacement part designed for use with chainsaws. It is made out of metal and it is sold individually. This is the part that fits over the bar and it is what cuts the material. Over time the chain will stretch and become dull so it will need to be replaced. To replace this chain you would need a wrench, scre...Read morewdriver and pliers. • Remove the buide bar side panel • Release the chain tension • Remove the old chain • Loosen the tensioning screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This is an authentic Poulan replacement chain designed for use with chainsaws. It is a key component of a chainsaw which mechanically cuts the material. Over time the chain will stretch, become dull or break. Keep an eye on the condition of the chain and replace as needed. Please note this chain is only for use with 16" bars. Includes one...Read more (1) metal cutting chain per order. The only tool needed for this repair is the scwrench that most likely came with your chainsaw. Otherwise, a flat head screwdriver and a socket wrench will do just fine. • Remove the guide bar side panel • Release the chain tension • Remove the old chain • Loosen the tension screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts