14-308 Tappan Cooktop - Instructions

un-pluged stove,removed the one screw holding the broken igniter. disconected the one wire. installed new igniter and slipped on wire. The igniter came with a new bracket, the old one rusted away which is why the old igniter broke.

The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igni ... Read more ter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.

no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter

Removed all of the grates, control knobs and gas diffusers. Unscrew the drip pans, two on each pan, which attach the pans to the gas supply. Raised the drip pans from the top and unplugged the ignitors from all pans. Remove the top and the rubber deflector over the ignitor switch. The ignitor switch snaps off and on. One of the seals unde ... Read more r the drip pan was broken and needed replaced. I would recommend ordering these also. Turned out this was a good time to give everything a goo cleaning then replace as removed.

Burner set screws froze up, was able to break 2 of 3 free and broke 3rd off. Used new simular screws to re- thread and fasten burner back in place. Bit of work but everything working. Used oppertunity to clean and re-level while I was at it. Everything good to go.

If you intend to replace the igniter electrode ( part no. PS436633), purchase a minimum of twelve (12) top burner mounting screws ( part no. PS437925).

I also recommend that you replace all the electrodes since you have gone to the lengths described below to replace one igniter electrode.

After time, the heads of the ... Read more mounting screws become brittle and break off when attempting to remove them with a 3/16" socket or nut driver.

Be aware that even the new screws are not exactly 3/16 hex, nor do they truly accept a 4.5 mm, or 5 mm socket. The 5 mm has to much slop, and the 4.5 mm, and 3/16" do not fully seat over the head.

First unplug the stove, and turn off the gas.

To remove the broken screws, I had to use a hand grinder to grind the heads off (you could be as careful as possible, but you will still damage the porcelain finish of the range top.) Unfortunately every screw has to be removed to lift the range top up enough to gain access to the electrode(s).

Along with the broken screws being in the burner casting, to replace the electrode, you have to remove the burner to work on it. Remove the insulated wire from the electrode, and then the gas line to the burner.

I recommend inspection of the insulated wires to see if they may be grounding out to the stove body. With the top removed and the burners still in place, plug the range back in. Turn any knob on (all electrodes should spark at the burner accept the bad one(s)). Observe the wires to see if there is sparking to the stove body. If there is none, continue to replacement instructions. If a wire is sparking to the body, wrap the damaged wire with HEAT RESISTANT tape. Standard vinyl electrical tape won't withstand the heat.

To remove the burner from the gas line, use a 1/2" open end wrench (preferably a tubing nut wrench) to remove the gas line along with an adjustable wrench to hold the burner to prevent damaging the gas line.

If your lucky, the cross point (Phillips head) screw that secures the electrode will remove without stripping, but don't count on it. I had to grind those screw heads off as well.

I used a size no. 30 cobalt drill in my drill press to attempt to remove the broken off screws, but because of the screw/drill size, I could not keep the bit on the hardened screw center, it kept walking off center. I ground the screws flush to the burner surface, used a center point drill, a center punch, and a spring loaded set point punch, nothing worked to keep the bit from wandering off center and into the soft metal casting.

I had to drill new holes with the no. 30 drill bit just to the right (or left) of the existing holes. Keep the same orientation and mounting distance when drilling, either to the right or to the left.

The new burner mounting screws did not work for mounting the electrode to the burning, I used small no. 6 self tapping screws to mount the new electrodes to the burner casting (the washer head was to large).

Reconnect the gas line(s) to the burner(s). It will be necessary to carefully bend the gas lines so as to line the new holes up with the top when remounting the burner(s).

If I had it to do over again, I would just donate the range as is, while explaining the problem to the donation center. After my experience, I personally don't think it is worth the trouble of replacing the electrodes on a range this old.

Hope this helps.

switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju ... Read more st the spark module for the burner.

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

The electrode was sparking to ground through the cracked ceramic rather than within the ignition zone. I used spray electronic contact cleaner to free rusted screws (different metals often contract at different rates and separate under the very cold spray). Replacing the electrode was a simple substitution. Also sprayed the spade termi ... Read more nal pair to remove any corrosion. Worked first time.

part match perfect, right part right price good company

The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.