138-242-100 (147088 - 170600) Cub Cadet Lawn Mower - Parts

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Extension Spring measures .62 x 6.12 inches. It is a silver, metal, individually sold, part. It can be installed with pliers and has been rated Easy to install by customers. (Note: Installation may require a lot of pull force to remove and reattach.) The spring attaches underneath the tractor on the drive belt idler pully, to t...Read morehe axle support bracket, and is used to apply tension on the drive belt idler pully. If broken or overly stretched, likely due to fatigue, you will lose your forward and reverse drive, as the belt will no longer be able to transmit power. If this happens, the part must be replaced. Refer to your owners manual and model number to ensure you are selecting the correct part.

This authentic component is specially designed for MTD riding lawn mowers and garden tractors. It is supplied directly from the original equipment manufacturer. The ball joint is an important part of the steering mechanism. Over time it may wear out or get damaged eventually requiring a replacement to keep your unit functioning properly. ...Read morePlease make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality ball joint is made of durable metal with a rubber component and is sold as an individual item. You need a screwdriver and a wrench set to take apart the housing and perform this repair.

This is a genuine OEM lube fitting part made for use with various outdoor lawn equipment models and measures 3/16-inch wide. Sold as an individual part, this grease/lube fitting is made of metal and is used to deliver lubrication to whatever it is attached to for better performance, through a small passage in the fitting. If your lube fit...Read moreting needs to be replaced, it may require pliers and a hex wrench for that process. Check your user manual or any diagrams to make sure this is the correct part for your equipment.

It is an authentic manufacturer-sourced component which is specially designed for lawn and garden equipment. The flange bearing helps to provide a tight fit between connected components. Over time it can wear out, get damaged or lost eventually requiring a replacement. This part is made of high-quality material and is sold individually. C...Read moreheck the diagrams for your model to ensure the exact location and the correct application of this hardware.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi and MTD lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hex washer screw. Ke...Read moreep in mind this high-quality part is made of durable metal and is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.

This screw is a high quality hardware that is specially manufactured for use on MTD and Yard Machines lawn and garden equipment. It is an authentic part that has multiple uses depending on the equipment. Make sure to check appropriate diagrams for correct location and applications of this screw. Please note, one hex head screw is included per order that will require a wrench to install or remove it.