1357 - Parts

This magneto, also known as an ignition coil, is a genuine OEM replacement part for outdoor power equipment. It generates the spark needed to ignite the air-fuel mixture in the engine’s combustion chamber, ensuring smooth and reliable operation. Over time, the magneto may fail due to worn wiring, damage to the spark plug lead, or incorrec...Read moret gapping between the coil and flywheel. Symptoms of a faulty magneto include misfiring, hard starting, and poor performance. Installation involves removing the spark plug for safety, accessing the flywheel, and setting the correct gap with a feeler gauge before securing the new part.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during the replacement of this item. It may become broken and will need to be replaced. This is an authentic Briggs & Stratton and Toro replacement...Read more part that is sourced from the original manufacturer for use with engines, snowthrowers, tillers, lawn mowers, and lawn tractors.

This fuel tank is for lawn and garden equipment engines. Fuel tank holds the gas that's needed by the engine. Work in a well-ventilated area when installing this part. Drain the existing fuel from the tank and disconnect the spark plug wire before beginning the repair.

This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin. To complete this repair you would need a wrench and pliers.

The O-Ring is a black rubber part, used to provide a seal between two pieces. It can be used in various locations on a variety of equipment. Installation is rate as "Easy" and will require a screw driver, pliers, socket set, and wrench set. If broken, damaged, or worn due to fatigue, you will have a leak and the part must be replaced. Refer to your make, model and diagrams to see if this is the right part for you.

The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will require a wrench set and socket set. If broken, damaged, or worn due to fatigue, there may be oil leaking from it, and the engine may be running r...Read moreough from an unwanted vacuum sucking in air. If this happens, replace the part. Refer to your make, model and diagrams to ensure this is the correct part for you.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This choke return spring is an OEM direct from Briggs & Stratton. The metal spring is compatible with several small engines. This component works from the choke system, applying the necessary tension to maintain the choke lever position. A screwdriver, wrench and pair of pliers are often required for the repair. The choke return spring is sold individually.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.