12AD566N711 (2004) Troy-Bilt Lawn Mower - Parts

This is a genuine OEM replacement part, it is sold individually. This is the front wheel on the models shown below. There are two of them on each mower. The wheel has a ring gear on the inside which is driven by the Right hand and Left hand smaller gear that attaches to the front axle on the transmission assembly.

This authentic replacement blade is manufactured for use with Craftsman walk-behind lawnmowers and is designed to deliver clean, efficient cuts. Measuring 21 inches in length, the blade features an angled design that promotes optimal airflow, allowing grass clippings to circulate through the cutting deck for effective side discharge and m...Read moreulching. Over time, mower blades can dull or wear down, leading to torn grass blades and a less polished lawn appearance. Replacing a worn blade with this high-quality part ensures a sharper, cleaner cut that keeps your lawn looking its best. This blade is sold individually.

This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, req...Read moreuiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation requires a hammer, 5/8 socket and torque wrench, and is rated as "Easy" by our customers. If broken or damaged (likely due to fatigue) you m...Read moreay hear a rattling sound coming from it, and the part should be replaced. This part is dark gray/silver, individually sold, and measures approx 3.5 x 1.25 inches. Refer to your make, model and diagrams to check if this is the correct part for you.

The Side Discharge Deflector, also known as a discharge chute, is a black plastic part used to direct glass clippings out from under the deck of the mower. This manufacturer-certified part has been rated as "Easy" to install by our customers. If broken or damaged, it must be replaced.

This item is a genuine OEM replacement part that is intended to be used with snowthrowers and lawnmowers from Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The metal hex head screw is used with different types of machines and the application of the screw can vary based on the model of the equipment. This screw is sold as an individual replacement part.

This is a Genuine Manufacturer Approved replacement part used on a variety of Lawn and Garden Equipment. This screw has different applications depending on your equipment. This item is made out of Metal and is Sold Individually. Requires a Wrench to tighten or loosen.

This replacement rear wheel is an authentic OEM sourced item that is specially designed for walk-behind lawn mowers. This is the rear wheel that supports the unit, please note that the front drive wheels are sold separately. This durable plastic wheel is sold individually, to replace it you will need a wrench.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

This Star Knob, which may also be simply referred to as a Knob, is sourced directly from the manufacturer for use in lawn mowers and snow blowers. This part provides a quick-release for handles to fold down, and connect upper and lower handles. It is made of metal, is black, is not part of a kit or assembly, and is sold individually. Th...Read moreis part will need to be replaced if it has become cracked, worn, or damaged. The most common cause for this part needing to be replaced is worn or stripped threads no longer being able to grip. You will need a wrench or socket set and a torque wrench to complete this repair. It should be torqued to the manufacturer's recommendation. Customers rate this repair as Easy.