129-366B029 (1989) MTD Tiller - Parts

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing...Read more it, inserting the cable into the new holder, and tightening it until it is locked in place.?

The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand upper handle, using a screwdriver and pliers, and is rated as Medium difficulty to install. This kit contains the parts that control the ...Read moreamount of the air and fuel entering the engine. When the part breaks (likely due to fatigue) you will no longer be able to control the engine. If nothing happens when you move the handle, that means it has become disconnected. When the part is broken it must be replaced. Check your model number to ensure you are selecting the correct replacement part.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

This is an authentic MTD tiller replacement part. The hex B-tap screw is used to fasten the cable barrel holder to the clutch lever to ensure good tension on the clutch cable. The part is made of durable metal. You will need a wrench to replace this piece. This item is sold individually.

This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually. This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.

This is an original replacement part sourced directly from the manufacturer. The throttle wire is commonly found in MTD tillers. This part is a metal cable with a flexible plastic casing, and it is used to connect the throttle control in the handlebar assembly with the engine. You may require a screwdriver or Allen wrench when replacing this product. This item is sold as an individual replacement part.