1265 - Instructions

First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly ... Read more easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c ... Read more an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

Removed the old one installed the new one

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the lo ... Read more cation and design of the switch. I got it though.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, ... Read more so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

Turn off the breaker. Remove the two screws holding the bake element and disconnect the two wires. Plug the new element in and re install the screws. Trip the breaker back on and test the oven. It works.

Turned power off by switching off the breaker. Removed both racks from oven. Removed two Phillips head screws at back of oven securing the old heat element. Pulled old heat element forward about four inches exposing the two power wires connected to it. Removed the wires from their connectors. Removed old element. Connected new element to ... Read more power wires and pushed it back in place. Replaced new Phillips head screws. Replaced racks, and turned power back on. Oven was fixed in less than five minutes. Disposed of old element. Life is good.

Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.

put the old one out,put new part in that easy,works like new

Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.

Loosened the two screws holding the element, pulled the element out of the back of the oven, loosed the two wire leads connected to the back of the element, removed the broken part, placed the new element into the oven, reconnected the wire leads, pushed them back into the insulation in the back of the oven, repositioned the element into ... Read more its place and replaced the two screws holding it into place with the new screws that came with the new part. Oven element fired right up first try without any further complications. One of the easiest appliance fixes I have ever done!

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed ... Read more the previous procedures to complete repair.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.