EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

125K02-0197-E2 Briggs and Stratton Engine - Instructions

All Instructions for the 125K02-0197-E2
1 - 7 of 7

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Mower was submerged in Hurricane Matthew
25 of 51 people found this instruction helpful.
  • Morris from HOPE MILLS, NC
  • A Bit Difficult
  • More than 2 hours
  • Wrench set
Total disassemble, clean out water and any rust. hone cylinder, wire brush where needed,reassemble with new rings,gaskets and seals and lucas oil product. Started on second pull. Mowed lawn. If you have never done this sort of work before, probably should not attempt.
Was this helpful?
Thank you for voting!
Smelled Gas Leaks
8 of 11 people found this instruction helpful.
  • Jonathan from LIBERTY TWP, OH
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.

Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Was this helpful?
Thank you for voting!
Replace carburetor
9 of 19 people found this instruction helpful.
  • David from KNOXVILLE, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Loosened engine cover and moved out of the way
Removed air intake and filter
Loosened and disconnected gas line to carburetor
Unscrewed carburetor and disconnected from throttle arm
Reversed process using new carburetor, O-ring and gasket
Was this helpful?
Thank you for voting!
Mower body was die cast and in good condition. Engine was burning oil.
5 of 8 people found this instruction helpful.
  • Robert from TEGA CAY, SC
  • Really Easy
  • More than 2 hours
Removed engine, no specialty tools required. Honed the cylinder, and lapped the valves. Tip on compressing valve spring for reassembly; compress springs with you finger and tie them with 2 zip ties, cut the zip ties after installing the keepers. Repainted the mower deck and engine. It runs and looks like new. My Toro is a 1999 model .
Was this helpful?
Thank you for voting!
blower housing on the customers log splitter broke.
1 person found this instruction helpful.
  • david from JERSEY SHORE, PA
  • Really Easy
  • 30 - 60 mins
blower housing on my brothers log splitter broke at the anchor points and caused the pull start to break and come apart. I was able to buy the parts and fix the log splitter for half the price of a new motor, saving him about $300.00.
Was this helpful?
Thank you for voting!
Leaking gaskets
4 of 12 people found this instruction helpful.
  • Dustin from BANGOR, ME
  • A Bit Difficult
  • More than 2 hours
  • Socket set, Wrench set
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
Was this helpful?
Thank you for voting!
All Instructions for the 125K02-0197-E2
1 - 7 of 7