123C (2004-03) Husqvarna Trimmer - Parts

This ready-oiled air filter is an OEM part that traps dirt and debris, preventing them from entering the engine. This part is black, comprised of foam, and is sold individually. Your air filter may become dirty and clogged over time, and because it is oiled, it is difficult to wash because it is oiled, so it will need to be replaced. A cl...Read moreogged air filter will cause your engine to run rough from restricted air flow. This is an easy repair to make and does not require any special tools.

This OEM fuel line, or hose, is a 4-inch, clear, plastic tube which is sold individually. It is rated as "Easy" to install. This part connects to the purge assembly and delivers fuel to the carburetor or is used as a return line to the tank. A broken hose will leak, and should be replaced. Refer to your make, model and diagrams to check if this part is right for you.

The air cleaner knob, just over 1 inch in diameter, is black in color and made of plastic. It is sold individually, and its function is to tighten the air cleaner cover down on various lawn and garden equipment. This knob can become worn over time, which will cause the air filter cover not to stay in place. Most of our customers find this to be an easy repair. It does not require any special tools.

This replacement screw is an authentic Husqvarna part. It is a genuine manufacturer approved part commonly used on a variety of power equipment including chainsaws, trimmers and sweepers. This standard hardware is utilized in many different placed depending on a tool. Please make sure to check appropriate diagrams to verify correct locati...Read moreon and application for this screw. It has hex head that will require a wrench to install or remove it and it is sold individually.

Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually. This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.

This OEM carburetor mixes the air-fuel mixture to the proper ratio for combustion in your engine. This carburetor is sold individually, is silver in color and metal in material, and is located on the intake of the engine. Issues with your carburetor will cause problems with your engine running, and could cause excessive smoke due to too...Read more much gas. This can happen due to corrosion inside the carburetor. Carburetors can be rebuilt easily, and repairing them requires an allen wrench and a screwdriver. When troubleshooting your carb, remove the air filter and pour a teaspoon of fuel into the carburetor. Pull the starter rope, and if the engine starts then quickly dies, the carburetor is likely the problem. When replacing your carburetor, also replace all gaskets when doing so, as they are a one-time use.

This fuel hose is a genuine OEM part designed to deliver fuel from your fuel tank to the carburetor. Also known as the fuel line, it is black in color, made of rubber, sold individually, and can be attached to your machine on the fuel tank and the carb. Over time, it is possible the line breaks due to wear or drying out. If you notice c...Read moreracks or leaking fuel, it is time to replace the fuel hose. This is an easy repair according to most of our customers, and does not require any special tools.

This is an authentic OEM sourced replacement screw designed for use with a variety of Husqvarna power equipment. It is a standard hardware which has multiple applications based on your tool. This part is made out of Metal and it is Sold Individually. Requires a Hex Key or a Wrench to tighten/loosen this Screw.

This is a rubber primer bulb with a plastic adapter attachment that is used on a variety of lawn and garden equipment models. This bulb attaches to the carburetor and is used to pump gasoline from the fuel tank into the gas chamber of the carburetor. Over time and through regular use, the primer bulb will lose its elasticity and may crack...Read more, requiring it to be replaced. To replace your primer bulb, you simply need to locate the bulb on your machine, unscrew the housing and remove the bulb, and secure the new one. This bulb is sold as an individual part and has a 2.25cm (7/8-inch) outer-diameter and a 3.33cm (1.3125-inch) height.

This is a genuine OEM part. The Husqvarna choke control is made for use with many lawn and garden trimmers. The plastic component is fastened to the carburetor, allowing the operator to manage the engine's fuel and air mixture. A hex key and a wrench may be required for making the repair. The choke control is sold individually.

This O-ring is a genuine OEM replacement part designed for use in a variety of power tools. It is a rubber seal used to prevent pressure loss, as well as oil, fuel, and air leakage from the fuel hose. It can be found on either end of the hose. You will need to replace this ring if it has lost elasticity, or if it is cracked or deformed. T...Read morehe O-ring can fail due to age, exposure to heat and chemicals, pressure buildup, or poor installation. A faulty ring will result in leakages, pressure loss, and decreased equipment performance. Carefully pry the old O-ring off the hose. Remove any dirt or debris in the area and lubricate the new ring before placing it in position. Apply light pressure to the ring until it is secure and sitting snugly. Note that your equipment may have several O-rings, therefore, inspect all of them as each ring is sold individually.