- Home
- 12-1663-45-01
- Instructions
12-1663-45-01 Tappan Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven would no longer light
0 of 1 people
found this instruction helpful.
-
Sherry from New Smyrna Beach, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..
Was this helpful?
Thank you for voting!
oven wouldn't light
0 of 1 people
found this instruction helpful.
-
matthew from Plainfield, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I
... Read more
was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.
Read less
Was this helpful?
Thank you for voting!
no flame
0 of 1 people
found this instruction helpful.
-
joe from newport beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
removed the old igniter, installed the new one. 15 minutes, piece o cake!
Was this helpful?
Thank you for voting!
Had a problem igniting the gas.
0 of 1 people
found this instruction helpful.
-
Danny from Bremerton, WA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.
Was this helpful?
Thank you for voting!
Igniter would glow but no gas would turn on
0 of 1 people
found this instruction helpful.
-
Ronald from brockton, MA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal
Was this helpful?
Thank you for voting!
oven would glow but would take a long time to light, and you could smell gas
0 of 1 people
found this instruction helpful.
-
patricia from mayport, PA
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
the igniter is real easy to put in
Was this helpful?
Thank you for voting!
No heat, gas smell in oven
0 of 1 people
found this instruction helpful.
-
David from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Was this helpful?
Thank you for voting!
igniter would heat up but burner for oven wouldn't
0 of 1 people
found this instruction helpful.
-
Robert from Inlet, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Took the two nuts off that hold the igniter and cut the wires as per directions and used the wire nuts to put them together after I installed the igniter.was a piece of cake and didn't take 15 minutes to do.Oven works great.
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
Christy from North East, PA
- Really Easy
- Less than 15 mins
It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy
The oven is working great and now I am back to baking.
Thanks for everything
Christy
Was this helpful?
Thank you for voting!
Igniter would glow but no gas would come out
0 of 1 people
found this instruction helpful.
-
Cornelius from Chicago, IL
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I removed the bottom plate of the oven to get a better view. I then removed the burner plate and the burner. Disconnected the igniter and put in new one it was real simple.
Was this helpful?
Thank you for voting!
There was a glow in the oven but the oven wouldn't heat up
0 of 1 people
found this instruction helpful.
-
sean from spring grove, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people
found this instruction helpful.
-
Patrick E. from Washington, PA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
I just sent in a generic description of my problem and a couple of ideas on what it might be. Within 2 days an online repair person answered me back with the solution. I ordered the part and 2 days later I was back in business and baking cookies.
Was this helpful?
Thank you for voting!
oven whouldn't come on or if it did it whould take along time to come on and stop after awhile
0 of 1 people
found this instruction helpful.
-
Ralph from Garfield Hts., OH
- Really Easy
- 30 - 60 mins
-
Socket set
pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove
... Read more
it
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
Read less
Was this helpful?
Thank you for voting!
Oven Would Not Light
0 of 1 people
found this instruction helpful.
-
Neil W. from Westerville, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed
... Read more
simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh
Read less
Was this helpful?
Thank you for voting!
oven slow to warm and gas smell
0 of 1 people
found this instruction helpful.
-
JONATHAN from DEARBORN, MI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean i
... Read more
n there MUCH better.
Read less
Was this helpful?
Thank you for voting!