12-1663-00-01 Tappan Wall Oven - Instructions

could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!

removed the old igniter, installed the new one. 15 minutes, piece o cake!

took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.

took off bottom pan in oven and replaced ignitor

took out the old (2 screws) put clip on wires and put the new part in. Simple

wonderful went perfect!!!

i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as wel ... Read more l with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself

I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so muc ... Read more h money doing it myself. U to can do it, good luck!!

after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com

From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than i ... Read more t had for some time.

This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ... Read more ired our stove myself!

After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!

removed bottom plate in oven removed three screws and cut two wires.

Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor ... Read more by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.