1159132 Troy-Bilt Lawn Mower - Parts

This authentic replacement blade is manufactured for use with Craftsman walk-behind lawnmowers and is designed to deliver clean, efficient cuts. Measuring 21 inches in length, the blade features an angled design that promotes optimal airflow, allowing grass clippings to circulate through the cutting deck for effective side discharge and m...Read moreulching. Over time, mower blades can dull or wear down, leading to torn grass blades and a less polished lawn appearance. Replacing a worn blade with this high-quality part ensures a sharper, cleaner cut that keeps your lawn looking its best. This blade is sold individually.

This trail shield, also referred to as a rear skirt, is designed for use with various makes and models of lawn mowers and is a genuine OEM part. This trail shield is sold as an individual part without its securing hardware, and measures 16.5-inches long and 4.5-inches wide. It features a notch on both sides to secure it to the rear of the...Read more mower chassis and prevent glass clippings, dirt and other debris from hitting the user. This shield is made of durable plastic, meaning over time it can crack, and when your current trail shield is broken or damaged, it is crucial that you replace it. To replace it, remove the bag from your mower and simply lift out the old shield and install the new one.

The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation requires a hammer, 5/8 socket and torque wrench, and is rated as "Easy" by our customers. If broken or damaged (likely due to fatigue) you m...Read moreay hear a rattling sound coming from it, and the part should be replaced. This part is dark gray/silver, individually sold, and measures approx 3.5 x 1.25 inches. Refer to your make, model and diagrams to check if this is the correct part for you.

This replacement screw is a genuine item that is sourced from original equipment manufacturer. It is a high quality hardware that is commonly used with walk-behind lawn mowers. This screw has multiple uses depending on your model. Please make sure to check appropriate diagrams for correct location and use of this hardware. You will need a wrench when working with this screw.

Wing knob screw 1/4-20 x 1

Also referred to as a Lock Nut or Flange Lock, this nut is designed for use with various lawn and garden equipment. The purpose of this part is to hold parts in place while resisting loosening when properly threaded. It is sold individually, not as part of a kit or assembly. It is black, made of metal, and is found in a variety of locatio...Read morens. Refer to your owners manual to determine if this is the correct part. This part will need to be replaced when it is weak or broken. The symptoms experienced when this part breaks will depend on its location. You will need pliers to complete this repair. Customers rate this repair as Easy.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This is a genuine OEM sourced replacement part designed for use with lawn mowers. This wing knob helps to secure upper and lower handles on a mower. It is made out of red plastic and it is sold individually. Please note carriage screw is sold separately.

This genuine OEM replacement part is used on walk behind/push mowers. This cable consists of a metal wire cable with z-type bent ends and rubberized cover/body. The control cable stops the blade when the control handle is released on walk-behind mowers. If the cable is broken it will cause the brake to not release even when the lever is p...Read moreressed. You may need pliers to complete this repair. • First you want to see where tje old cable is attached to the motor assembly. • Just remove the cable end there and install the new one, • Now you can run the new cable up to the control handle • Then just as the old cable, put the z-shaped end through the hole in the control handle • Once both ends are attached, just push the upper mount assembly of the old cable out of the hole in the upper handle • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

This genuine screw is supplied directly from the original equipment manufacturer for use with Craftsman walk-behind lawn mowers and snowblowers. Check the diagrams for your model to ensure the correct repair procedure. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restra...Read moreins the screw and keeps it from turning when the nut is tightened. This screw is made of high-quality metal and is sold individually. A wrench might be needed to replace this hardware.

Looking for a way to breathe new life into your Whirlpool appliance? The Whirlpool PANEL ASSY, SERVICE CONTROL is the genuine OEM part you need. Designed specifically for select models of Whirlpool appliances, this crucial part ensures the smooth operation of your appliance's most important functions. High-performance, reliable, and buil...Read moret to last, it's proof of Whirlpool's dedication to delivering top-quality, durable components for your appliances. With this part, your machine won't just work?it'll work like new. Because parts can look similar but differ in subtle ways, always double-check the part number to make sure it's the right fit for your model. So why wait? Give your appliance the care it deserves and keep it running efficiently with the Whirlpool PANEL ASSY, SERVICE CONTROL. With this crucial replacement part, you're not just maintaining your appliance?you're enhancing its performance.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.