1130SWE (2002) Cub Cadet Snow Blower - Parts

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the ...Read morecontrol handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

This item is a genuine OEM replacement part that is intended to be used with snowthrowers and lawnmowers from Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The metal hex head screw is used with different types of machines and the application of the screw can vary based on the model of the equipment. This screw is sold as an individual replacement part.

Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature multiple of these bearings, so refer to any diagrams for your model to determine whether you will need one, or more. This is an OEM part that...Read more is sold as an individual item and has a 0.75-inch inner-diameter, 1-inch outer-diameter, and 1-inch height.

This is a worm gear that is designed for use within a variety of snowblowers and snowblower tractor attachments. The worm gear is used to rotate the auger through the drive mechanism, also known as the transmission. Featuring an approximately 2-inch diameter, this worm gear is made of high-quality, durable metal and is sold as an individu...Read moreal part. The worm gear will likely be secured in place using bolt or other fastener, and replacing this gear will require a wrench set and screwdriver. Make sure to check any user manuals or diagrams for exact placement of the worm gear within your snowblower.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This is a genuine OEM sourced part that is not part of a kit or assembly and is sold individually. This Spring Extension, or Extension Spring, serves a variety of purposes, depending on your model. It is black, made of metal, and may be found in multiple locations on your machine. This part needs to be replaced when it is worn, weak, dam...Read moreaged, or broken. Depending on its purpose, you may no longer have control of your machine when the spring breaks. You will need pliers to complete this repair. Customers rate this repair as Easy.

An extension spring is designed to add tension and resistance to different components throughout lawn and garden equipment. This extension spring, also known as an idler spring, is designed for use with the auger within different makes of various lawn and garden equipment like lawnmowers and snowblowers. This spring is approximately 2.5-i...Read morenches long when completely wound and is made of high-quality metal. If you notice that the lever that connects to the auger is loose or has significantly less tension than normal, this spring could be broken or have lost its level of tension, meaning it needs replacing. To replace this spring, you may need a set of pliers, but you simply remove the frame cover over the spring, pull it away from the auger, and carefully pull it off. Then, simply replace that old spring with the new spring.

This metal flange bearing is an authentic manufacturer-sourced component which is designed for use in lawn and garden outdoor equipment. It is bronze in color, with 6 six flat sides, and it has an inner diameter of 0.75 inches, and a height of 1 inch. It also features a protruding circular rim on one end, known as a flange, which keeps th...Read moree bearing stable and secure. The bearing serves as a support mechanism, allowing rotating parts to move smoothly with minimal friction. Over time the bearing may wear down, crack, or fall off causing excessive noise, reduced performance, and potential damage to the snowblower impeller or auger. Use a bearing puller tool to pry the bearing off the equipment. Align the new flange bearing with the mounting holes and secure it in place.

This authentic part is supplied by the original equipment manufacturer and is specially designed for use with snowblowers. The extension spring is utilized to apply tension on the auger belt idler arm. Unfortunately, over time it will wear out and it may begin to stretch eventually requiring a replacement. This high-quality extension spri...Read moreng is made of durable metal and is sold individually. Make sure to check the diagrams for your model to ensure the proper repair procedure.