1130ST Snow Blower - Parts

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This chute base, also known as a discharge chute base, is sourced from the original manufacturer for use with snowblowers. It is found at the end of the discharge chute which is responsible for directing the discharge of snow, or other materials that are being thrown by the equipment. The chute base is found at the end of the discharge ch...Read moreute where it acts as a connection point between the chute and the auger housing. The chute base aids in directing the discharge to a specific place, as well as controlling how far the discharge is thrown. If the chute base becomes damaged, cracked, or worn out, it will need to be replaced. A faulty chute base will result in snow being thrown haphazardly, not being thrown far enough or not thrown at all. It can also create blockages in the equipment, leading to potentially expensive repairs. Remove the fasteners that secure the base to the equipment and pull off the old chute base. Align the new chute with the mounting bracket and secure it with the fasteners.

This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the ...Read morecontrol handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

This item is a genuine OEM replacement part that is intended to be used with snowthrowers and lawnmowers from Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The metal hex head screw is used with different types of machines and the application of the screw can vary based on the model of the equipment. This screw is sold as an individual replacement part.

Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature multiple of these bearings, so refer to any diagrams for your model to determine whether you will need one, or more. This is an OEM part that...Read more is sold as an individual item and has a 0.75-inch inner-diameter, 1-inch outer-diameter, and 1-inch height.

This is a worm gear that is designed for use within a variety of snowblowers and snowblower tractor attachments. The worm gear is used to rotate the auger through the drive mechanism, also known as the transmission. Featuring an approximately 2-inch diameter, this worm gear is made of high-quality, durable metal and is sold as an individu...Read moreal part. The worm gear will likely be secured in place using bolt or other fastener, and replacing this gear will require a wrench set and screwdriver. Make sure to check any user manuals or diagrams for exact placement of the worm gear within your snowblower.

This manufacturer approved replacement part is designed for snow blowers/throwers. Skid shoe/plate allows you to avoid damage and keep smooth control over cracks, gravel, and other uneven surfaces. It is made out of metal and it is sold individually. Please note the right skid plate is sold separately. It is advised to replace both skid ...Read moreplates at the same time. To complete this repair you will need a wrench. • First remove bolts holding old skid plate • Remove old plate and insert new skid plate • Level snow blower and adjust skid plates to desired height • Tighten skid plate bolts

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

The deflector spring is made of metal and attaches to the deflector assembly. This spring is available as an individual replacement part. It will need replacement if it becomes stretched or broken. It is used in Husqvarna, Poulan, and Jonsered snowblowers and is an OEM from the manufacturer.

This is a genuine OEM sourced part that is not part of a kit or assembly and is sold individually. This Spring Extension, or Extension Spring, serves a variety of purposes, depending on your model. It is black, made of metal, and may be found in multiple locations on your machine. This part needs to be replaced when it is worn, weak, dam...Read moreaged, or broken. Depending on its purpose, you may no longer have control of your machine when the spring breaks. You will need pliers to complete this repair. Customers rate this repair as Easy.