1107224401 Kenmore Washer - Instructions

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

First I removed the two screws on the back of the control console( at the bottom, phillips head). Flip that up and out of the way. Then you could remove the 2 big clips that hold the back of the washer to the cabinet. Disconnect the lid switch and flip the cabinet forward and out of the way. Remember when putting the cabinet back on, ... Read more line up the slots on the bottom of the cabinet with the toungues on the base. Next pull off the fabric softner dispenser, then reach down in there and pull out the bottom seal of that to expose the bolt that hold the agitator on. Remove that bolt and pull off the agitator. Remove that little clip and the plastic piece above the spanner nut. I didn't have a spanner wrench so I hade to use a small extension from my socket set and a hammer to loosen it. Once that is removed then you could remove the ring around the top of the tub, and pull the tub off. Now you could see the block and probably all the metal shavings it's been creating. If the two ears that stick up and fit in to the block are worn, you should replace that too. I think you hve to replace that from the bottom. Now just put it all back together. Print out the exploded diagram from the web sit so you have it right there. Good luck!

replace the water valve

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. ... Read more Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

Removed the old one installed the new one

Easy, If your drive block has an open top, it's worn. Look at a picture of a new drive block and compare. If it doesn't match, then you need a new drive block. Note: Also check the drive clutch and clutch liners or pads...they may be worn. In my case it was the drive block this time. So to start, take off the fabric softenner dispens ... Read more er in the center of the washer. Then pull out the seal. then remove the bolt. and pull off the agitator assembly. after that tap off the lock nut with a punch and hammer or if you have the special spanner wrench tool, use that. Once removed, pull out the inner tub and then pull the drive block off the shaft. Put the new drive block on and reverse the procedure from there. Tap the lock nut tight with the punch and hammer while re-installing. I'm so glad I did this repair. $15 is so much better than just giving in and buying a new washer!!!

I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred th ... Read more e bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the lo ... Read more cation and design of the switch. I got it though.

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, ... Read more so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed ... Read more the previous procedures to complete repair.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an ... Read more d into bushing. 5)Reinstall hinge pin retaining screws and tighten.

Oredered late Friday afternoon. Got part Monday afternoon.thanks