11068133410 Kenmore Dryer - Parts

This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If damaged or broken the dryer will not dry properly, will not tumble properly, or may not even start. Installation is rated as "Medium" diffic...Read moreulty. This part is located on the dryer drum, around the tension pulley. Refer to your user manual and model number for repair instructions and to ensure this part is right for you. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers.

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the...Read more part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Y...Read moreour model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

The idler pulley with bracket ensures proper tension on the dryer’s drive belt, allowing the drum to spin effectively. This assembly includes the pulley and arm, making it ideal for replacing a worn or damaged component. Designed for various Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dryers, this genuine OEM pa...Read morert guarantees reliability and performance. If your dryer is noisy or the drum is not turning properly, this part may be the solution. Always disconnect power and wear gloves during installation.

This door catch Is an authentic OEM replacement part that is designed to fit with dryers. It is responsible for keeping the dryer door securely closed while it is running. When the door is closed, the catch engages with the door strike and snaps into place, holding the door shut until the drying cycle is completed. Over time the catch may...Read more become corroded, worn down, or damaged, or dislodged from frequent use and hard impact. If the catch is faulty, the door may be unable to remain shut. This can lead to heat loss, injury, and potential damage to the dryer itself. If the catch is no longer functional, it is recommended to replace it as soon as possible and avoid using your dryer until the repair is complete.

Sold individually.

Sold individually.

This part is an electrical connector where you can attach wires. This part does NOT included the wires, screws, and nuts. Must be order separately

Introducing the Whirlpool Dryer Idler Spring, a genuine OEM part designed for some models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef clothes dryers. This essential product functions to hold the idler pulley tight against the drum belt, enabling the belt to turn smoothly and efficiently. Specifically designed...Read more for the idler pulley arm in dryers, it ensures optimal performance of your appliance. Guaranteeing maximum durability and reliable performance, safety measures include unplugging your dryer before installation and wearing work gloves to protect your hands. Opt for the Whirlpool Dryer Idler Spring to maintain the effectiveness of your dryer. Please verify that this part is suitable for your model before ordering to counter any potential variations in size or shape.

This kit includes 3 screws and 3 nuts.

Sold individually.

This screw is sold individually.