1106405901 Kenmore Washer - Instructions

We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.

Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a ... Read more nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. ... Read more I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

very easy

The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th ... Read more e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab ... Read more out 10 minutes.