1106315801 Kenmore Washer - Instructions

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechan ... Read more ical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab ... Read more out 10 minutes.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ... Read more ss fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

The door would not close after installing gasket. Used liquid soap around edge of gasket, this worked.

Replaced the cap over the door switch so when the door closed the switch was engaged

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in ... Read more a few days. Problem solved. Thank you

I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.

Replaced actuator switch lever. Exact replacement. Worked like a charm.

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came a ... Read more cross your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clo ... Read more thes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it ... Read more was listed below along with the cost. Couldn't of been easier. Thanks!