1106004603 Kenmore Washer - Instructions

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

Replaced actuator switch lever. Exact replacement. Worked like a charm.

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came a ... Read more cross your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed ... Read more the previous procedures to complete repair.

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred th ... Read more e bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.

Removed the old one installed the new one

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. ... Read more Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clo ... Read more thes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing b ... Read more ack together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid an ... Read more d into bushing. 5)Reinstall hinge pin retaining screws and tighten.