1105805 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
The dryer would not run.
0 of 2 people
found this instruction helpful.
-
Kevin from North Aurora, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in
... Read more
a few days. Problem solved. Thank you
Read less
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 2 people
found this instruction helpful.
-
Edwin from Shelby, NC
- Easy
- Less than 15 mins
-
Screw drivers
Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.
Was this helpful?
Thank you for voting!
Actuator Switch lever broken
-
Steven from Howes Cave, NY
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced actuator switch lever. Exact replacement. Worked like a charm.
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
door switch actuator had broke
-
Dale from Sparta, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap
Was this helpful?
Thank you for voting!
Dryer would not start
-
John from Sackets Harbor, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came a
... Read more
cross your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!
Read less
Was this helpful?
Thank you for voting!
dryer door switch broke
-
Jeff from Mamaroneck, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.
Was this helpful?
Thank you for voting!
Dryer door switch actuator spring broke.
-
Anthony Di from Farmingville, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.
Was this helpful?
Thank you for voting!
The spring lever broke at the bend after 26 years of use.
-
Mark from Crestview, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.
Was this helpful?
Thank you for voting!
Washer leaking
-
Forrest from Oxford, AL
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this.
... Read more
Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Read less
Was this helpful?
Thank you for voting!
My dryer would not work when I closed the door.
-
Michael from Hudson, NH
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it
... Read more
was listed below along with the cost. Couldn't of been easier. Thanks!
Read less
Was this helpful?
Thank you for voting!
Dryer won't start
-
Michael from Cincinnati, OH
- Easy
- 15 - 30 mins
-
Screw drivers
Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.
Was this helpful?
Thank you for voting!
actuator spring lever broke
-
george from port angeles, WA
- Easy
- 15 - 30 mins
-
Screw drivers
two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clo
... Read more
thes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened
Read less
Was this helpful?
Thank you for voting!