Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11026332500 > Parts

11026332500 Kenmore Washer - Parts

All parts for the Kenmore Washer 11026332500

Below is a list of all parts for the Kenmore Washer 11026332500. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 11026332500
1-14 of 171
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added ...

$2.84

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched out and lost its spring, it could cause the load to be off-balance which can cause excessive shaking, moving, noise and possibly leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screw driver, and a pair of needle nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually.

$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpoo...

$44.29

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to the machine not draining properly, leaving your clothes wet after a cycle. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate the need to replace your clutch. This clutch assembly comes with a brake cam driver, blue springs for large capacity washers, and a black spring for compact washers. As per the factory, the green spring (1.24 inches) replaces the black spring (1.46 inches). This repair requires a half inch 1/16th socket with an extension and a ratchet, a pair of channel lock pliers, a Phillips screwdriver, medium size flat blade, a small flat blade, and a 1/4 inch nut driver.

$30.63

Water Inlet Valve with Mounting Bracket

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-color...

$23.02

Switch, Lid

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. You will need a 5/16-inch nut driver for this repair. The package will contain one lid switch. You will need to access the back of the washer, and remove the two Phillips screws that hold the top back panel in place. Slide the panel forward to release. Use your nut driver to loosen the screw that holds the ground wire in place. Lift the lid of the washer to release the old lid switch.

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$12.08

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$6.88

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$4.28

GASKET

This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.

$2.81

Foot, Front - Single

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a ru...

$16.30

Suspension Pads - Package of 3

$18.64

Drain Hose

It connects from the pump to the back panel. The clamp is not included.

$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

All Parts for the 11026332500
1-14 of 171