110200 Kenmore Washer - Parts

This shift actuator is a genuine replacement component designed for top-load washing machines. It plays a critical role in transitioning the washer between agitation and spin cycles by shifting the transmission and monitoring the splutch position. Equipped with a synchronous motor, it regulates the agitator’s movement to ensure proper was...Read moreh performance. Compatible with a wide range of models from Whirlpool, Maytag, Kenmore, Amana, and other associated brands, this part is commonly replaced when the washer fails to start, agitate, or spin properly. Symptoms of failure include slow spinning, no agitation, or the drum not turning despite the pump running. Installation requires basic hand tools and novice repair experience. Always disconnect power and water before beginning. Sold individually.

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.

This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality...Read more materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.

Sold Individually.

This insert is sold individually. Knob not included. Knob is sold separately.

Metallic screw that is less than an inch long. Does not include the plastic washer.

This part is the replacement lid seal for your washer. It is made of rubber and is gray in color. It is approximately 21 inches long and 1 inch wide. The washer lid seal creates a seal for your top load washer and prevents leaks. If your washer is leaking from the lid, or if you are having difficulty closing the washer lid, the lid seal m...Read moreay need to be replaced. The lid seal will also need to be replaced if it is worn out or damaged. This part is sold individually and is sourced directly from the manufacturer. This is an authentic OEM part.

This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, your washer door may not close properly and you may not be able to run your washer. The latch is found under the lid and can be screwed out and...Read more replaced. You will need a Phillips-head screwdriver for this repair. This part is sold individually and is and OEM part from the manufacturer.

This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring ret...Read moreainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cleaning the tub, pump, and internal components, helping to eliminate unpleasant smells and maintain optimal performance. Safe for use with se...Read moreptic systems, this cleaner is intended for monthly use?simply place one tablet in an empty washer and run a Normal Cycle with hot water or a Clean Washer Cycle. Regular use can help extend the life of the appliance and ensure fresh, clean laundry results. Always follow the instructions provided for best results.

This is a pack of three suspension pads for your washer. The suspension pads in your washer are found underneath the tub and prevent the rotating metal parts from grinding on one another. If your suspension pads are worn out, you will likely hear metal-on-metal grinding, which is an indication they need to be replaced. It is recommended to replace all three suspension pads at the same time.