1100P - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I ... Read more have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!

Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to ... Read more the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.

2 screws easy to remove and plug in the wire. job done.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a ... Read more brand new oven!

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They include ... Read more d a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.

Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Suc ... Read more h a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and ... Read more 7. re-assemble steps 3,2,1. Easy

I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation ar ... Read more ound wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & ... Read more completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.

was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!