110-075R000 (1990) MTD Lawn Mower - Parts

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

This operator presence cable is a genuine OEM replacement designed for walk-behind lawn mowers. It connects the handle bail to the engine brake system, ensuring the engine stops immediately when the handle is released for safe operation. Built for reliable performance with correct cable length and fittings, it’s an ideal replacement when ...Read morethe mower won’t shut off properly or the original cable is stretched, frayed, or broken.

This is a genuine OEM sourced replacement screw which is commonly utilized on lawn and garden equipment. It is a standard hardware which has multiple applications based on the model of your unit, please refer to appropriate diagrams for the correct location and use of this part. It is a high-quality hex head screw which is made of durable...Read more metal and it is sold individually. Over time threads may wear out or it may simply get lost eventually requiring a replacement, note that a wrench will be needed to install or remove this hardware.

This discharge chute is a genuine OEM sourced replacement part that is specially made for walk-behind lawn mowers. It is mounted to the side of the mower deck to direct the grass clippings away from the unit. This item includes the durable plastic chute with the metal hinge bracket assembly which is used to secure it to the deck. Please n...Read moreote that the hardware to attached this discharge chute is not included, it is sold separately.

This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually. This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.

This is an authentic OEM part for use with MTD, Yard-Man, Troy-Bilt Lawn Mowers. The drive control cable engages the gear case to drive the lawn mower. The most common reason for replacing the control cable is if it is broken, causing the brake to not release even when the lever is pressed. The tool that you will need to replace the drive control cable is pliers.