10RJ736H Hotpoint Range - Instructions

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set ... Read more .

Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element fr ... Read more om the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.

Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. ... Read more Attached the bracket and I turned on the power. I then tested the oven and it worked.

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which wor ... Read more ked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after re ... Read more connecting the new element the broiler tested OK. It is once again broiling steak to perfection

Removed 4 screws and removed the old element and replaced in the reverse order.

Removed 3 screws from cover {center of back side of oven}, removed 2 screws from wires connected to element, then removed 2 screws mounting element
{inside oven}, pulled it & replaced it.

less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...

extremelyquick delivery on standard mail and so easy to install and really the lowest price. so happywith this company

After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.

Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that ... Read more hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!

I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.

The replacement was straightforward, six screws. Instructions were provided with the part along with the necessary screws to fit the new element terminals.
Open the breaker, verify power is off, remove the old burner. Install the new burner and mounting bracket. Restore power and test. In and out in less then thirty minutes.

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened w ... Read more ith the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.