All Installation Instructions for 1078

Burner burned out

Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!

Parts Used:

6" Heating Element

Daniel from Norborne, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner didn't go on

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

Parts Used:

Large Haliant Burner with Limiter - 8"

Mike from Hatfield, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

End cap broke on handle

Opened oven door removed screw and broken end cap. Replaced with new end cap and put handle back on

Parts Used:

End Cap - White - Right Side

Jim from NORTH HAVEN, CT
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bad sensor

By myself

Parts Used:

Oven Sensor

John from CASPER, WY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

only the inner/smaller part of the dual burner is working

I ordered a new burner assuming As is turns out: nothing wrong with the burner.

Parts Used:

Dual Radiant Element - 9 Inch

Albert from South Boston, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

small (inner) burner was not 'burning'

turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members

Parts Used:

Dual Radiant Element - 9 Inch

Jerry from Tierra Verde, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

dropped & broke the oven light bulb cover

popped the new one on!

Parts Used:

Light Cover

joseph from san jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Just follow the enclosed instructions

Followed the instructions

Parts Used:

Oven Sensor

HAROLD from Tucson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

cooktop inner ring did not work

Dear PartSelect:

I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.

I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.

Matt Brennan

Parts Used:

Dual Radiant Element - 9 Inch

Matthew from Lexington Park, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Oven handle broke off

Couple of screws and it was done. Simple and inexpensive since I thought I was going to have to buy a new range.

Parts Used:

Door Handle

Maureen from Locust Valley, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

the paint started to chip off.

remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy

Parts Used:

Bottom Trim - White

vanessa from runnemede, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Two stage burner was not working on the outer part of burner.

Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.

Parts Used:

Dual Radiant Element - 9 Inch