106978556 Kenmore Ice Maker - Instructions

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in ... Read more the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.

After locating the screws, removed icemaker, disconnected cable connection.

Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, conne ... Read more cted wiring harness, tightened screws. Waited for ice to arrive about an hour later.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was i ... Read more ce! Everybody was happy.

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. T ... Read more he lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.

remove the ice bucket support bracket and remove bottom screw from icemaker, loosing the two top screws and slide icemaker back enoughto unplug electric harness

Removing the hex screws from the existing unit was trouble until I found the screwdriver attachment to the hex wrench. The MOLEX type power connector was an exact match for what was on the unit, so the conversion cables were not needed. Unit worked fine. No more leaks.

I took out the bottom locking screw and loosened the top two screws. I took the old icemaker out. I disconnected the wiring harness at the ice maker. I attached the new icemaker and mounted it in place. I didn't have to use any of the included wiring harnesses since the old one worked fine. I did use the old wire bale. I'm fairly un ... Read more gifted in fixing things so I was amazed at how easy and inexpensive this was. The icemaker started up right away. The whole thing probably cost less that just the service call minimum would have been.

I watched the demo on how to replace the ice marker and it was that simple. I removed three screws and unplugged it from the freezer. The difficult part was removing the wire on, off switch. You must pull it out carefully. It is a sung fit.

Removal was easy...Removing and installing arm was a bit difficult...Called a service man to install...He also had a bit of difficulty, but had it done in less than 45 minutes... He mentioned that my brackets had a different set up than most...

I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails ... Read more to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.

I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice ma ... Read more ker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.