1069659722 Kenmore Refrigerator - Instructions

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causin ... Read more g the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

Slipped track into grooves, and wha-la!! Easy fix, quick order turn-around, part realidy available for a ten year old appliance. Overall, could not have been a better experience.

Took out the cracked one, and replace with the new one. Fitted perfectly.

Took cardboard cover off rear of refrigerator, five screws. Turned water off and unplugged fridge. Took out two screws holding inlet valve, pulled off quick release power wires and changed out water supplies in and out. Rebooked power and replaces cardboard cover. With power and water back on, ice maker was supplied with water.

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left ... Read more no questions.

decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

NO DIRECTIONS CAME WITH GASKET! Project failure as gasket tore on a corner. For the price of this gasket, I was DISAPPOINTED. Door is being held shut with a childproof strap.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

This is an incredibly easy repair.

1) Remove the three screws holding the old icemaker

2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip

Do the opposite to install the new icemaker.

Total elapsed time was about 5 minutes.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m ... Read more e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Removed crisper drawers removed glass shelf installed Rail.
Replaced glass shelf then installed crisper drawers.

1. Removed the icemaker door
2. Removed the two screws from the underside of the icemaker unit
3. Removed the slide-on plastic cover that protects the power cable connector
4. Removed the icemaker unit
5. Removed the two screws from the control unit
6. Pulled the control unit from the icemaker unit
7. ... Read more Installed the new control unit and reinstalled the icemaker assembly

A repairman wanted to charge me $250 to do what I did in about 20 minutes for about $120.

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So ... Read more far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of ... Read more scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.