- Home
- 1069608211
- Instructions
1069608211 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Internal light did not come on each time the door was opened.
0 of 1 people
found this instruction helpful.
-
John from Jefferson Hills, PA
- Really Easy
- Less than 15 mins
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical
... Read more
outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Read less
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people
found this instruction helpful.
-
Cecelia from Beaver Dam, WI
- Easy
- 15 - 30 mins
-
Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
After Hurricane Irene refrigeration compressore did not start
1 of 4 people
found this instruction helpful.
-
Bobby from New Bern, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.
Was this helpful?
Thank you for voting!
19 year old light switch broke
0 of 1 people
found this instruction helpful.
-
Fred from Watertown, NY
- Really Easy
- Less than 15 mins
Great service. Unpluged old switch and pluged in new one. Works great
Was this helpful?
Thank you for voting!
replacement bar on door
0 of 2 people
found this instruction helpful.
-
Doug from Quincy, MA
- Easy
- 15 - 30 mins
ordered the wrong part at first. Spoke to a service assistant, returned it and got the right part. Cut it to fit and inserted it. The Service assistant was very helpful, wish I used her first rather than the online system.
Was this helpful?
Thank you for voting!
Magnets don't work very good
1 of 5 people
found this instruction helpful.
-
Emma from Lake Alfred, FL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver
took old one off and put the new one on.
Was this helpful?
Thank you for voting!
The refridgeror side was not cold enough
0 of 2 people
found this instruction helpful.
-
Patrick from Sun City, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people
found this instruction helpful.
-
Ronald from Billings, MT
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
Read less
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people
found this instruction helpful.
-
Joseph from Destin, FL
- Really Easy
- Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
Noisy defrost timer
0 of 2 people
found this instruction helpful.
-
Jeffrey from Little Falls, NY
- Easy
- Less than 15 mins
-
Nutdriver
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people
found this instruction helpful.
-
Janet from Flagstaff, AZ
- Easy
- Less than 15 mins
-
Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
Starting relay went out
5 of 18 people
found this instruction helpful.
-
George from Conroe, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigg
... Read more
ed a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.
Read less
Was this helpful?
Thank you for voting!
change relay
3 of 12 people
found this instruction helpful.
-
Robert from Boxborough, MA
- Easy
- 15 - 30 mins
-
Screw drivers
unplugged relay and plugged in
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!