10696082 Kenmore Refrigerator - Instructions

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator bran ... Read more d new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.

Each side of the door had a metal strip bracket that was held in place by 1/4" sheet metal screws apprx. 8in. apart.. the outer lip of the gasket was tightened into these brackets..loosening the screws allowed the removal of the gasket from all 4 sides and corners..It was just the process of fitting the new gasket into the brackets that t ... Read more ook the most time..making sure the new gasket was fitted all the way in for aligned proper fit,then tightening the screws evenly around the door frame..Then, 2 weeks later, this 27-year-old refrigerator's lower compressor went out,,and the refrigerator was history! YEAH!!

with vidio

After searching online to diagnose the issue with my refrigerator being warm and the freezer being cold and not shutting off to defrost I decided to get the defrost timer kit. The kit arrived within 2 day. With the directions included, after unplugging the appliance for safety, I installed it relatively quickly with only a screwdriver . I ... Read more then plugged it back in and it immediately went to defrost. I thought, wow I have it fixed. Well unbeknownst to me it still didn't cool in the fridge area. After doing more internet research I found a suggestion to unplug the fridge for 24 hours to unthaw ice that may be lodged between the freezer and fridge that is blocking the distribution of cold air into the fridge. After doing this, it now works like a charm.

Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

Like you video