106941589 Kenmore Ice Maker - Instructions

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

Removed old water valve on bottom right back side of fridge installed new one which actually took less work

The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi ... Read more tting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice ... Read more maker. Gregg in PA.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. T ... Read more he lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was i ... Read more ce! Everybody was happy.

Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.

After locating the screws, removed icemaker, disconnected cable connection.

Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, conne ... Read more cted wiring harness, tightened screws. Waited for ice to arrive about an hour later.

Removed bottem screw and loosened two top screws. Removed icemaker from support screws and disengaged cable. Replaced in reverse order. Total time was about 15 minutes.

Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.

. ... Read more . . thanks!