106939001 Kenmore Refrigerator - Instructions

Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.

Easy removel: remove one screw and loosen two others; unplug connector; swap actuator bar; replace

Removed three screws and unpluged wiring. Replaced new unit by plugging in wire and replacing three screws.

Lossen two screws at the top and remove one at the bottom and lift the unit off of the top screws, unplug the old unit and after cutting out the tray for the water fill spout plug the new one in. No problem .................

Removed the old ice maker and replaced with new.

I watched the demo on how to replace the ice marker and it was that simple. I removed three screws and unplugged it from the freezer. The difficult part was removing the wire on, off switch. You must pull it out carefully. It is a sung fit.

remove the ice bucket support bracket and remove bottom screw from icemaker, loosing the two top screws and slide icemaker back enoughto unplug electric harness

Removing the hex screws from the existing unit was trouble until I found the screwdriver attachment to the hex wrench. The MOLEX type power connector was an exact match for what was on the unit, so the conversion cables were not needed. Unit worked fine. No more leaks.

I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice ma ... Read more ker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.

I took out the bottom locking screw and loosened the top two screws. I took the old icemaker out. I disconnected the wiring harness at the ice maker. I attached the new icemaker and mounted it in place. I didn't have to use any of the included wiring harnesses since the old one worked fine. I did use the old wire bale. I'm fairly un ... Read more gifted in fixing things so I was amazed at how easy and inexpensive this was. The icemaker started up right away. The whole thing probably cost less that just the service call minimum would have been.

Removal was easy...Removing and installing arm was a bit difficult...Called a service man to install...He also had a bit of difficulty, but had it done in less than 45 minutes... He mentioned that my brackets had a different set up than most...

Parts arrived amazingly fast. Replaced top ice maker and bottom water control valve[which was probably the source of my problem all along] in about an hour. The online installation video's were a big help. Thanks.

The old water valve leak required me to purchase this new complete part. After shutting off the water supply, disconnect the supply line, take out the old water valve by disconnecting the "plug" from the refrigerator, and disconnect the plastic water line going into the ice maker. Then just reconnect the new water valve by plugging it i ... Read more nto the 2 pronged receptacle, note to be sure to write down which wire goes into which input when disconnecting the old valve. Then hand tighten the plastic tube into the valve. Next attach your water supply line into the new water valve, tighten this supply line as you would any plumbing supply line with a couple of adjustable wrenches and some teflon tape at the connection. I would also recommend at this point, if the compression fitting on your supply line was like mine a bit old, to spend a couple bucks on a new fitting and put that on the supply line, since you don't want to worry about it being a good seal at the supply line point, once the repair is done. After checking for "no leaks" reattach everything to the rear of the refrigerator (make a note of the attachment before taking out the old valve) and see if your ice maker starts to make some ice. You will hear the valve feeding the water to the icemaker if all is properly setup.

I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.

Very simple repair. Ice maker was operating, but not receiving water. Once new valve was in place it works like new.