1069209580 Kenmore Freezer - Instructions

Like most have stated this is a simple job. Nut-driver and six screws (on mine). Less than ten minutes. Like someone else said the hardest part was unloading the door.

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical ... Read more outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus ship ... Read more ping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00

I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old

I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks

I removed the door (three screws on top). Flipped the door upside down, removed the cams, and replaced with the new ones and replaced the door. Now the door closes great. The only problem is that the door sort of "clunks" into place when I open or close it. I am not sure that I used the right cams. The drawing on the directions was n ... Read more ot at all clear.

I am a single female so the hardest part was lifting the door off and then trying to get it back on the hinge. I used the same bolts that were on the door so putting the new parts on was the easiest part. The slowest part was finding the right socket for the bolts and unscrewing the originals. Beats hiring a repair man.

I removed the door and replaced the door cams and reinstalled the door

it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty

The parts were delivered promptly. I ordered the kit assembly because I didn't know which part was the problem. Reading the remarks from other people's symptoms and solutions made the process much easier. I replaced both the upper and lower cams. Lubricated the cams and reinstalled the door.. Problem solved!!!!

Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both ca ... Read more m surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!

1. Used fine tip marker pen to draw outline of upper hinge position

2. unloaded food from door

3. took decorative cover off upper hing mount

4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.

5. lifted door off lower hinge.

6. ... Read more remove broken pieces, cleaned, put in new pieces, added small amount of grease

7. put door on bottom hinge.

8. put top hinge into door

9. snugged up three screws in top hinge plate.

10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed

Best part was PartSelect save me bunches of money and got parts quickly

rem upper hinge on door on & lifted door off. installed kit provided & ressemble.