106894 Kenmore - Instructions

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself

removed the front cover below the compartment door,removed the 2 screws holding the valve to the case and removed the water lines from the valve.The process was reversed to install the new valve.

Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibil ... Read more ity. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.

just replaced the water inlet valve, it took less than 10 minutes. Ordering the part was just as simple, no hassle what so ever. Got the part as promised and installed it in minutes just as it was explained. I will come back to this site in a hart-beat.

Thanks

Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.

Disconnected both water lines and two mounting screws. Installed new water lines and water valve. No problems at all. Ordered the valve on a Monday and received it the next day. Even though i chose FedEx ground. GREAT SERVICE! I am a technical service manager and I always give credit to company's with great service. In fact, I have sent y ... Read more our website link to our management team to show what our website could be for our customers. Easy to find part numbers, pictures of the part being ordered and ease of use. World Class support.
Kindest regards,
Dave

Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy wi ... Read more th parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company

r&r fan blade and motor. with the parts you supplied it was easy. the parts were perrrrfect. thank you very much. job well done. bruce

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other tor ... Read more x screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.

Water was not being drawn from the reservoir to the evaporator plate, so I concluded that the recirculation pump had failed. I first unplugged the machine from electrical power. To improve access to the pump, I removed the cutter grid using a nut driver and squeezing the electric connections to separate them. I also removed the reservoir, ... Read more first removing the drain pipe by pulling it downward and the using pliers to loosen the thumbscrews until I could turn them by hand. I then thoroughly cleaned both the cutter grid and the reservoir to improve performance once the repair was done. The pump is covered by a solid plastic screen attached by just one nut, which is removed easily with the nut driver. The pump itself is attached with three screws which are easily removed with the nut driver and by an electrical connection which loosens by squeezing. Indeed, Upon examination, i found that the pump shaft was stuck solid and did not turn freely, explaining why it did not work. Replacing the pump, reattaching the three screws and reattaching the electric connection was pretty easy except for the right rear screw behind the pump which was hard to reach to guide the screw without a trick up my sleeve. The trick was to wrap scotch tape around the screw and the nut driver so that I could guide the screw one-handed. Once the screw threaded through a few turns, I jerked back the nut driver, pulling the tape off the screw. I then removed the tape from the nut driver and continued to tighten that screw and the rest, and then reattached the electrical connection. I then reattached the screen, the reservoir and the cutter grid, then plugged my machine back into the electric circuit and was pleased to watch it hum back to life, good as new and performing better than it was before the pump had failed.

buy unplugging thermisistor machine should stop making ice.buy loosening the top cover and front cover you can access the plug and thermisistor.

removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

I used the cleaning solution that I purchased from you and my ice maker is now working perfectly !!!!

Thanks for the fast shipping !!

Happy Holidays !!