1068766310 Kenmore Refrigerator - Instructions

Looked up on youtube. found a guy who said that the shaded pole motors are made in china and rotate backwards. (design flaw) so, he had a 4 minute tutorial on how to reverse the motor and it runs the correct way.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi ... Read more tting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice ... Read more maker. Gregg in PA.

I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

Simply removed the old and replaced with the new part.

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

Pulled out the stud with a wire cutter and replaced it with the exact part you shipped in the kit.

The other 2 parts just slipped on the brackets

Nice thing is now I have extra parts for the other shelf.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i ... Read more s inside the refer!

Took just a few moments to install. The parts fit like a glove,

Replaced missing stud.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

The first issue was to determine if the problem was with the ice maker or the water dispenser / pump. I chose to try to repair the dispenser first since there air bubbles in the plastic line. Also, the ice maker seems to have been working. There just wasn't enough water so the ice cubes were hollow.

I unplugged the power cor ... Read more d, , removed the cardboard backing and two bolts that secured the pump to the refrigerator. I vacumned the area so I could see around. I pulled the valve out and disconnected it from the internal power source. I disconnected the copper water intake and the plastic tubbing to the ice maker. I used a pipe cutter to take the old flanged area off. A new flange was included in the package. I used that and reconnected the copper intake and the plastic tubbing. I replaced the power source and secured the valve to the refrigerator makeing sure the plastic tubbing wasn't twisted. When I plugged the refrigator back up, the ice maker started working within five minutes.

Very simple repair. Ice maker was operating, but not receiving water. Once new valve was in place it works like new.