1068690313 Kenmore Refrigerator - Instructions

Just moved into a new rental home and a few days in the bar that holds all the stuff -- milk containers, juice jugs, etc. -- in the refridge door falls off. The old tenants had "fixed" it with tape on one side and paint stirrers and caulk on the other side. (No kidding -- a real overkill job they did).

I looked up the model num ... Read more ber online and found this site and promptly ordered the parts for $6 plus shipping. The parts came and snapped right in perfectly. Took only a minute.

I really only had to use pliers to pull out the oodles of hard swirly caulk from the slots in the door left from the overkill job by the previous tenants.

PartsSelect is awesome! The site makes it easy to look for the part you want and the parts were perfect -- No more stuff falling out the fridge door.

PS. This form made me select the age of the appliance. I really have no idea since I just moved in and it was already here.

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!

replaced retainers. remove and replace four(4) phillips screws.

Like you video

Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.

Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.

Removed door and replaced bushing bracket was ok.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi ... Read more er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.