1068638680 Kenmore Refrigerator - Instructions

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

yup

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a ... Read more single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world whe ... Read more re my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged th ... Read more e unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Pla ... Read more ce the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plug ... Read more ged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

Remove freezer shelves, panel, and change fan.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.