1068490010 Kenmore Refrigerator - Instructions

I read a previous entry that stated the stud needed to be twisted out, which was very useful. I was bit worried at first when I removed the broken one and a bit of the insulation came out and it seemed mangled inside, but twisting the new one in worked. It is in there firm and strong, good as original.

Replaced the capacitor per your video. Tested and the problem persisted. Next replaced the thermostat per your video. Tested and the unit functions properly. The challenge was the connector locations on the new thermostat were different than the original. Front and back instead of top and bottom. I could not find an answer for wire instal ... Read more lation. So I guessed and placed the double red wires on the spade closest to the door and the single orange wire on the rear spade. It worked this way and I did not try it the other way. Fridge is working and my wife is happy. Regards, Ricky

I follow the video From The Tech Guy ( Gentleman ). Thank you... Best Regards .Fco

Just followed the video supplied with shipment. 5 minutes, even for a mechanically-challenged person.

Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!

inserted stud and twisted

Turn off power .Remove the control knobs and pry off the front panel ,it just snaps on,Take out two screws holding the control panel Take out the two screws holding the control to the base of the panel to get at the two screws holding the control to the bracket. Ther are screws holding the covers over the thermostat tube. Then pull out ... Read more the tubbe and remove the plastic cover on the old control and place it on the new control tube. Then route the new tube into the snaps be careful to not make ant sharp bends in tubing.When that is done fasten the control to the bracket and fasten the bracket to the panel.Replace covers over tube to hide it and keep from damaging it when putting things in fridge.. Mount the conrol bracket back to the fridge and replace snap on cover. Plug in electric.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce ... Read more ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

First, after re-reading your descriptions here on your site ( it took clues from each of them) I unplugged the refrigerator and began on the only day my husband was out of town. The two selector knobs came off easily fingers only. The plate came off with only a slight prying with a screwdriver (it is intended to snap off this way). Loo ... Read more sening the screws and removing them in order to remember which order they returned proved to be a challenge. After disassembly, pulling the thermostat out of the tubing and replacing it with the new one without bending it was hard to do also. The refrigerator runs like new, and may run another eleven years! Thanks!

Replacing the support clips was simple. But since the replacements were the same as the ones that had failed, I modified them by epoxying metal strips on each side of the fingers which had failed. Without this mod I think they would have failed very shortly like the original ones did. This added a half hour to the repair.

My husband twisted the stud off and was able to put the new ones in quickly

Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic ... Read more k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

Just followed the Video I found on your site. Seems to work good now, took awhile to get temp setting correct (had to set it a little colder about half way between the "b" and "c" setting).