106846 Kenmore Refrigerator - Instructions

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking ... Read more the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

Replacing the support clips was simple. But since the replacements were the same as the ones that had failed, I modified them by epoxying metal strips on each side of the fingers which had failed. Without this mod I think they would have failed very shortly like the original ones did. This added a half hour to the repair.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce ... Read more ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right ... Read more direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!

1, Removed heavy items from door bottom two shelves.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hin ... Read more dge and lubricate cams with silicone grease.
7. Remove wood bracing.

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back ... Read more on and put the screws back in on the top hinge of the refrigerator door. Works great now!

I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.

Thanks so much! You saved me a bundle!!

Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.