1066667621 Kenmore Refrigerator - Instructions

I just removed three screws from the old ice maker and disconnected a single set of wires. All I had to do was reconnect the new set of wires and screw it back into the side of the freezer. Anybody could do this repair.

The ice maker is held in by three screws. There is an electrical connection. Also, there is a water line to the rear of the unit.
The replacement unit had clear instructions and a selection of parts to match the defective device.
Hint: don't discard the old unit until the new unit is configured for installation.
Turned on ... Read more the water and the electricity to the fridge, and had ice in several hours.

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, a ... Read more nd they agreed to replace the part. Could not be happier with the customer service I received from this company.

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making al ... Read more l the ice we need thanks

joan mcquain

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in ... Read more the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!

Removed two screws, pulled the element out and disconnected the wire harness. Reversed the procedure and we were one.
Kept a close watch n the ice maker to make sure we didn't have another flood. The first time an ice cube stuck between the metal bale and the side of the freezer--we had about 50 gallon of water on the floor. Thoug ... Read more ht we had it fixed and a few days later another flood. Decided to replace the unit and it is working great...Hopefully no more floods.

I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it ha ... Read more s taken me longer to write this reply than it did to install the icemaker.

This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!