106638 Kenmore - Instructions

The only tricky part of ordering replacement drawers for this fridge is that the bottom ones are two different sizes so you have to be sure you order the right one. Measure the width and look closely at the exploded drawing to be sure you are getting the right one.

I was about to waste $1000 on buying a Refrigerator. Took 1 mins to search on google "Refrigerator doesn't work". Found a video on youtube, showed a step and step video to solve my problem. Order the part $50 and it took me less then 5 mins to install it. =)

Removed 1/4 screw from housing to access thermostat. removed plastic tubing and three wires, reassembled and it works fine.
Repair took 12 minutes

I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker ... Read more from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.

First I ascertained that valve was faulty. Ordered replacement and installed without issue. Water now overflowed only during fill and found that filler neck had ice in it as a result of initial leakage. Defrosted with a hair dryer, removed ice plug and it now works as advertised.

Shut of both freezer and refer section, as well as unplug unit. Remove h2o line to bottom of frig that supplies ice maker. Remove back panel and set aside. Remove green, red and white wires from relay and start device. Be sure to mark which goes where, it may seem simple, but 3-5 days later when the parts arrive, things may look different ... Read more . Install the two replacement parts in the reverse order by which you removed them. Remember, white tabs are down and touch back of lower part when installed. Install panel and hto line, check for leaks, plug in and turn refer on.

Turn off the water supply.
Remove the two screws with a nut driver.
Disconnect the electrical connector.
Disconnect the water supply lines from the old valve.
Reconnect the water supply lines to the new valve.
(be sure to push the water line into the quick connect securely)
Reconnect the electrical connector ... Read more .
Re-install the valve with the two screws.
Turn water supply on.

I removed the screw that held the control module in place, then unscrewed & unplugged the circuit board and plugged the new one in. At that point I realized that the mounting bosses on the new piece were a quarter inch longer than the old one and the screws were now too short. The old bosses couldn't be adapted without wrecking them. Luck ... Read more ily I found screws out in the garage that worked. The screws that came with the new piece were the same as the old ones. Also they were packed loose with the circuit board and one was stuck between the protective cover and the pins. Thankfully it fell out on its own before I plugged the refrigerator in.

removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

Unplugged the machine removed the bottom plate and back plate and ice maker.Removed 2 wires to motor and ground wire.Removed 2 mounting nuts for motor,installed new motor and used old fan blade for new motor .Reinstalled in reverse order plugged in and tested fine.

We decided to use our crisper drawers to store sodas. Duh..bad plan. The rail that holds the drawers up cracked in half. So we just had the drawers sitting on the bottom of the fridge. So, I got the new rail THE DAY AFTER I ORDER IT! I just recycled the old one, and slid the new one in. Presto. Perfect fit. Actually, better then perfect. ... Read more There must have been a defect with my old one, because the new one actually SNAPPED into place, instead if just sitting in the frame. So..I am really pleased.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

changed the starter connected to the compressor

its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame ba ... Read more ck to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop

Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in ... Read more less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.