My Orders
1066021 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Surface Element switch faulty with no control on heat
1 person
found this instruction helpful.
-
Ramiro from AUSTIN, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma
... Read more
king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.
Read less
Was this helpful?
Thank you for voting!
handle broke off when my wife used it to brake a fall
1 person
found this instruction helpful.
-
Lawrence from FAIRFIELD, CA
- Very Easy
- 15 - 30 mins
Installled handle using existing screws tightening all after all screws were inserted. Part of the problem was that I weakened the original handle because I didn't know about the shield over the single screw on the front of the door. I purchased the unit at the Sacramento outlet and didn't get an instruction packet upon delivery.
Was this helpful?
Thank you for voting!
I had taken freezer door off when moving and misplaced the one of the hinges.
2 of 4 people
found this instruction helpful.
-
Darlene from Philadelphia, PA
- Really Easy
- 15 - 30 mins
I attached the hinge and secured it with screws and socket wrench.
Was this helpful?
Thank you for voting!
compressor not running
1 person
found this instruction helpful.
-
Doug from Lancaster, CA
- Really Easy
- 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 person
found this instruction helpful.
-
Yakov from BROOKLYN, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
Bottom part of refrigerator wasn't getting cold
1 person
found this instruction helpful.
-
Chad from RIDGEFIELD, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out
You guys are the best.
Called in and you guys helped out
You guys are the best.
Was this helpful?
Thank you for voting!
the bracket that holds the crisper drawer broke
1 person
found this instruction helpful.
-
Gerhard from SPRINGFIELD, NJ
- Really Easy
- 30 - 60 mins
I screwed the bracket in. How ever the placement of the screw made it impossible to use a small wrench. I had to manually tighten it. Having a screw head would have been better
Was this helpful?
Thank you for voting!
Rerigerator was leaving a lot of condensation on top shelf in refrigerator.
1 person
found this instruction helpful.
-
James from MEMPHIS, TN
- A Bit Difficult
- More than 2 hours
-
Pliers, Socket set, Wrench (Adjustable)
Removal of the door gasket went quite fast. First i needed a 8mm wrench. That what I didn't have. Got the socket set, not the wrench. Tried adjustable wrench, went slow. I slowly got the bolts out. Putting the gasket on was slow. Then I get to the last corner, was awful for me. I finally get it on. Putting the freezer door back on 1st we
... Read more
nt crazy. I finally looked on top of refrigerator, saw (3) bolts, removed them, installment went easy from there.
Read less
Was this helpful?
Thank you for voting!
Did not have ice maker
3 of 8 people
found this instruction helpful.
-
Marisa from TEMPE, AZ
- Very Easy
- 1- 2 hours
-
Nutdriver
Followed online video instructions
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people
found this instruction helpful.
-
David from GROVESPRING, MO
- Easy
- Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read more
s inside the refer!
Read less
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people
found this instruction helpful.
-
David Barnes from ROSWELL, NM
- Very Easy
- Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people
found this instruction helpful.
-
Kathy from TEMECULA, CA
- Very Easy
- Less than 15 mins
-
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
burned out freezer bulb
1 of 3 people
found this instruction helpful.
-
Tom from Midlothian, IL
- Really Easy
- Less than 15 mins
Remove plastic cover, unscrew bulb, screw the new one in.
Was this helpful?
Thank you for voting!
Doesn’t cool
1 of 3 people
found this instruction helpful.
-
Benjamin from WASCO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Work just perfect
Was this helpful?
Thank you for voting!
19 year old light switch broke
0 of 1 people
found this instruction helpful.
-
Fred from Watertown, NY
- Really Easy
- Less than 15 mins
Great service. Unpluged old switch and pluged in new one. Works great
Was this helpful?
Thank you for voting!