106584 Kenmore - Instructions

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace h ... Read more olding pins and start the process of putting back together the opposite way you took it apart.

Was very confused when the part sent out looked nothing like the one it would replace. There was a note in the package saying that this would replace it but I was doubtful. Suggest that it be made very clear that this is an upgraded part to replace a bad design.Had not problem once i checked the website and found this to be correct replac ... Read more ement part. I didn't have any problem with the order of the crusher blades as once I removed the shaft nut I slid all of the parts in order onto the awl. Then it was a simple matter of sliding them off of the awl onto the auger shaft. The new metal auger works much better than the plastic one it replaces.

Unplug the refrigerator. Snap off the ring surrounding the dispenser from the bottom. There are two slots on the bottom. This is the toughest part of the repair because my refigerator is older and the part stuck. Then unscrew the two hex screws and unsnap the parts, then reassemble with the new parts. Snap the ring back on and you're all ... Read more set. Pretty easy.

I first opened a beer to gain some liquid courage. The crowd (dog and 2yr old) were anxiously watching while I first grabbed hold of the refrigerator door. The door swung open with a mighty roar exposing the huge gaping whole where the previous crisper pan once shelved itself in glory. I took aim, and slid that new crisper pan in like it ... Read more was meant to be. The crowd went nuts...but probably because the tv commercial was over and Sesame Street was back on. Thanks partselect!

Removed the filter and put the cap on the new filter and inserted it as instructed on the filter box. Really easy now that we have the new cap.

I removed the cardboard backer board at the bottom rear of the refrigerator. I had to remove two screws to free the old inlet valve from the frame. The old water tube fittings were compression (screw on) type, so I cut the ends off cleanly with a sharp blade. They inserted into the valve holes easily - just needed a good push to lock ... Read more them in solidly. The tubes are different sizes, so it was easy to know which one goes in which hole - the electric connectors were easy to transfer from old to new... screwed the new valve back onto the frame, re-installed the cardboard backer, flushed the system -- and no more leaks!!

The old ice maker's protective finish flaked off causing some cubes to stick to the mold and consequently water overflow into the bin below causing ice cubes to fuse into large ice globes. After reading customrs' reviews, the replacement with new icemeker from PartSelect was easy. I unpluged the fridge, loosend two screws on top of ice ma ... Read more ker and removed one screw on the bottom, removed old ice maker and inserted the new one in its place. I reused the old wireing harness for new ice maker. It started producing ice within 2 hours and it works flowlessly since. Thank you PartSelect for sending the correct part and informative repair hints on your webside.

removed the Ice Tray, removed the cover that the motor is attached to, The biggest problem I had was getting the coupler off the drive shaft. It would not tightyen up and would not turn auger. I had to remove the unit and take a hack saw to cut the coupler off
The other problem I could not get the wireing harness unpluged from the ... Read more refigrator, and had to remove each individual wire from its contact. I had to remove the whole motor unit inorder to get the old coupler off.

Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ... Read more ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the le ... Read more ad wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

I removed the back cover to gain access to the compressor. I unpluged the start device and cap from the compressor. Replaced the items with the new ones. Plugged in the refridge and it worked. Whirlpool/Kitchenaid appliances are problems. I won't buy another.

The repair was actually easy; however I have an ice dispencer/crusher attached and the which the diagram supplied with the part did not include. I had to make several calls before I was e-mailed the diagram.
Suggestions: note that the screw at the end of the auger goes in the reverse direction (this took me about 20 minutes to fi ... Read more gure out even though it was shown in the diagram). Also, be sure to keep the ice crusher parts in order and be sure the white plastic tab on the crusher fits into a depression in the housing. I did not notice this and had to take it all apart and redo the install. It works great!!!

Removed all items from frig,put it on its back side,removed metal cover and removed housing screws,hoses.

It turn one turn on the filter holder, pull out and put new filter in done

replaced with new shelves