106572 Kenmore - Instructions

I assumed the motor had burned out. I removed the 4 hex-head screws to remove the bracket holding the motor. I had to squeeze the electrical fitting to the motor located in the right rear of the compartment in order to electrically disconnect the motor, since the lower part of the fitting has a latch that prevents its easy removal. Then ... Read more I could insert a vice grips on the shaft and on the coupling in order to (reverse) unscrew the coupling from the motor. I initially received the wrong replacement motor, but when the correct one arrived, it installed on the mounting bracket easily and I reinstalled the bracket with motor easily. It turns out a new motor did NOT fix the problem, so I'm not sure what to do now.

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts avai ... Read more lable for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I ... Read more put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.

Switched Electric breaker to off. Removed all food and ice cube tray from freezer. Remove 4 screws on soleniod cover in rear of freezer. Removed two screws, two elec connectors from old soleniod and removed. Installed new soleniod. Reinstalled elec connectors and screws, ice cube tray and food. Turned breaker on . Ice maker worked properl ... Read more y.

1. Turn off water supply to refrigerator.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors. ... Read more
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.

Just removed the old timer and attached the wires to the new one and replaced the old. That simple!

Used a volt meter to determine if compressor was getting power. It was not. There were only two wires going to compressor so I partially unloaded frige and disassembled unit until I found the control circuit. I removed the control board and could not find any degraded connections so I thought it was most likely the relay installed on the ... Read more board. I determined which connection was the normal power feed and decided that the relay should power one of two outgoing lines when it picked up. I jumpered from power to the most likely line and powered up the refrigerator and it worked. I cycled the breaker to maintain temperature until the new part arrived (about 2 days). I installed the new board in about 30 minutes and everything is working great. Looking forward to another 15 years with this refrigerator. It may be destined for the garage in a few years when we remodel the kitchen but it will make a fine shop frige!

I removed the outer ice/water dispenser cover following directions I found on-line (push down and gently pry out at the bottom). I then removed several nut-head screws which were holding a plastic plate which had the door light and electric control wiring mounted in it. Behind that I found a broken tab on the Control Bracket which was w ... Read more hy my water dispencer was not working and I found the chute door for the ice maker was chewed up which allowed warm air into the chute and was causing my ice build up problem. Replacing the Control Bracket was easy. Just note how things come apart. Putting the chute door in was a little more complicated, but again, note how things come apart and you should not have a problem putting it back together.

Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf

took back of refrigerator, removed water lines, removed electrical connections. removed 2 screws holding water valve, replaced water valve, replaced electrical connection, replaced water lines. Put back on refrigerator. Tested water on freezer door. Didn't work, had to take refrigerator back off again and check the electrical. I didn't g ... Read more et one of the connection put on securely, Put back on refrigerator, check water on freezer door. It worked. Make sure the electrical connection are connected this will sav you about 10 minutes of repair time

a simple replacement

Pretty easy to replace..just take your time with the ice crusher but the teeth are labeled a..b..and c. This auger is steel so I should have no problems with this breaking. I received this item less than 24 hrs after I ordered it! On Christmas eve...Thanks to all of you

The plastic lower door closing cam was worn down. Replacing it was very simple: remove the top door hinge by unscrewing three nuts; lift the door off the lower hinge; unscrew and remove the lower door hinge; screw the new plastic lower door closing cam on to the new door hinge; screw the new lower door hinge; lift the door back on to th ... Read more e lower door hinge; screw the top door hinge.

I had read here from someone that fixed there shelf support stub and it was very loose, so I was trying to advoid that problem. It took me less then 5 minutes and my only tool was a pair of pliers. A short turn clock wise from the 9 on a clock to the 12 ( which is the top left corner ). then pull the broke shelf stub straight out. Put t ... Read more he new shelf support in the same way you took the old one out and turn counter clock wise 1/4 or from 12 back to 9 and you should have a tight fit. I hope this helped.