1065111 Kenmore Refrigerator - Instructions

I emptied refrigerator contents and tilted the refrigerator to the right so as to access the metal panel upon which the evaporation tray was resting. The metal panel is on the left side underneath the refrigerator and the evaporation tray is resting on the panel. I removed 4 screws that were holding the metal panel, pressed down on the ... Read more panel, slid out the old, cracked plastic evaporation tray, inserted the new plastic evaporation tray, raised the metal panel to its original position, replaced the 4 screws, being careful not to pinched the water line that feeds the ice-maker. VOILA! Un-tilt the frig and re-stock it. It took a day for the temperature to stabilize, due to tilting, I think. New tray $45.

Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.

Removed six screws from cover in the back of the freezer. Removed old fan . Removed power wires from old motor. Unclipped old motor from the mounting bracket. Replaced old motor and reversed the rest of the parts. Done

Put new drawer in fridge.

The refrigerator would not come back on after the defrost cycle unless I smacked the housing around the controls. Since it would come back on after stricking the housing I knew it must be a sticking relay. I used the exploded drawings from Parts Select to determine how to disassemble the housing. Once the part arrived I swapped it out in ... Read more about 10-14 minutes. The drawings made the job simple. Thanks Parts Select!!! -neal

To get the coupler off the motor shaft I took two adjustable wrenches and slit the old coupler where it was cracked.The threads on the motor shaft were stripped closest to the motor.I took two thin washers and put them on the motor shaft so the new coupler would not turn down to where the threads on the motor were sripped.Since the thread ... Read more s on the coupler are left hand they keep the coupler tight as the motor turns the dispenser auger to dispense the ice.I was a bit difficult to unplug the wiring harness but got it after we used a screwdriver to keep the tab bent down until the harness was unplugged.

I discovered that the freezer was not defrosting automatically and the condenser coil was freezing up blocking the flow of cold air to the refrigerator side. I first replaced the thermostat thinking that it would be an easy fix but needless to say it didn't work. My indicator that it was not a successful repair was the continuing blinking ... Read more of the filter change light on the control panel. Ultimately I had to replace the control board assembly to solve the issue.

Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and ... Read more returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you ... Read more Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip ... Read more to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left ha ... Read more nded threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.

Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for le ... Read more ak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.

The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now ... Read more .

I slipped the shelf onto the brackets that already were on the sides of the refrigerator.

I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector ... Read more by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.